Paver Calculator
Pavers for a patio or path, laid out in the pattern you pick with every edge cut…
Pavers for a patio or path, laid out in the pattern you pick with every edge cut counted, plus the joint sand and the base under them.
Joint
Pattern
More options0% spare
Spares on top
The count already includes every cut piece. Spares cover breakage and a later repair.
ExamplePavers to buy
892pavers
778 whole and 114 cut. 49 slivers.
Enter yours to see your result.
- Polymeric sand, 50 lb bags
- 4
- Edge restraint
- 56′
- Patio
- 192 sq ft
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
How this works: 18 sources,
How this works
Method
Like the tile page, this one lays the patio piece by piece in your pattern, with the joint between pavers, and counts what falls inside the edges: whole pavers and cut ones, each cut using a paver. Herringbone at 45° or 90°, running bond and stack bond all cut differently at the edges, so the count changes with the pattern, which a square-footage division can’t show. Full method
Sources
- Interlocking concrete pavement guide specification (PAV-TEC-009-13) (Interlocking Concrete Pavement Institute / CMHA, 2013)
- HP NextGel polymeric sand data sheet (Techniseal, 2023)
- Emerald Interior Acrylic Latex product data sheet (Sherwin-Williams, 2023)
- BEHR PREMIUM PLUS Interior Eggshell Enamel No. 2050 technical data sheet (Behr, revised 9/2019)
- Dulux Trade Vinyl Matt data sheet 411 (AkzoNobel, 2025)
- Sheetrock Installation and Finish Guide (fastener, compound and tape calculator) (USG, 2003)
- Sheetrock UltraLight panels submittal sheet (sizes) (USG, 2010)
- Ultraflex 2 product data sheet (MAPEI, 2024)
- VersaBond Professional Tile Mortar, TDS-119 (Custom Building Products, 2026)
- Polyblend Plus Sanded Grout, TDS-360 (coverage chart) (Custom Building Products, 2026)
- Installation Essentials Guide for Laminate Flooring (Pergo)
- CRI 105, Standard for Installation of Residential Carpet (The Carpet and Rug Institute, 2019)
- Roofing Collection Product Guide (bundles, starter, hip and ridge, underlayment) (Owens Corning)
- Technical Note 10, Dimensioning and Estimating Brick Masonry (Brick Industry Association, 2009)
- Calculating wallpaper quantities (Farrow & Ball)
- Primed MDF baseboard mouldings (lengths) (Metrie)
- Decking Installation Guide (Trex)
- NIST Handbook 44 (2026), Appendix C: General tables of units of measurement (National Institute of Standards and Technology, 2026)
How it’s tested
One worked example for this page is checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: square footage of any rooms you draw, with paint, tile, drywall, flooring, carpet, roofing, pavers, brick, wallpaper, baseboard and deck board pages.
How the pavers are worked out
Like the tile page, this one lays the patio piece by piece in your pattern, with the joint between pavers, and counts what falls inside the edges: whole pavers and cut ones, each cut using a paver. Herringbone at 45° or 90°, running bond and stack bond all cut differently at the edges, so the count changes with the pattern, which a square-footage division can’t show.
The interlocking pavement guide specification gives joints of 1/16 to 3/16 inch and a bedding sand layer screeded to 1 inch, over a compacted aggregate base. The base and the bedding sand are worked out on the concrete calculator’s paver base and sand pages, from the same patio size.
Polymeric sand for the joints comes from Techniseal’s data sheet: a 50 lb bag covers 60 to 120 sq ft with narrow joints and 25 to 40 with wide ones. The calculator uses the narrow-joint low figure; small pavers and deep joints take more.
pavers = whole + cut pieces in the layout; polymeric sand = area ÷ 60 sq ft a bag
- Joints between pavers are 1/16 to 3/16 in; the bedding sand is screeded to a nominal 1 in. Source: Interlocking concrete pavement guide specification (PAV-TEC-009-13).
- A 50 lb bag of HP NextGel covers 60 to 120 sq ft with narrow joints, 25 to 40 with wide joints. Source: HP NextGel polymeric sand data sheet.
Pavers per square foot
By area with ⅛ in joints, before edge cuts.
| Paver | Per sq ft | Per 100 sq ft | Per 400 sq ft |
|---|---|---|---|
| 4 × 8 in | 4.30 | 430 | 1,719 |
| 6 × 6 in | 3.84 | 384 | 1,536 |
| 6 × 9 in | 2.58 | 258 | 1,031 |
| 12 × 12 in | 0.98 | 98 | 392 |
| 16 × 16 in | 0.55 | 56 | 222 |
| 12 × 24 in | 0.49 | 50 | 197 |
| 24 × 24 in | 0.25 | 25 | 99 |
Sources
- Interlocking Concrete Pavement Institute / CMHA, Interlocking concrete pavement guide specification (PAV-TEC-009-13)
- Techniseal, HP NextGel polymeric sand data sheet
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
How many pavers do I need?
For 4 × 8 in pavers with ⅛ in joints, about 4.30 per square foot before cuts, so a 12 × 16 ft patio is about 826 by area. The layout here counts the edge cuts too, which in herringbone adds noticeably more.
Which paver pattern is strongest?
Herringbone interlocks in both directions, which is why it is the usual choice for driveways, where cars turn and brake. Running and stack bond suit patios and paths and cut fewer pavers at straight edges.
What goes under pavers?
A compacted aggregate base (4 to 8 inches for patios, more for driveways, from the paver makers’ guides), then about 1 inch of bedding sand. Work them out on the paver base and sand pages and add them to your list.