Skip to content

RC Time Constant Calculator

The RC time constant from R and C, with the charging curve and 1τ to 5τ drawn.

The time constant of a resistor and capacitor, with the charging or discharging curve drawn and 1τ to 5τ marked. Plus charge time, energy, RC filter cutoff and capacitor codes.

Ω
F

Type values as printed: 4k7, 10k, 100n, 4.7µ (or 4.7u), 22p.

V

ExampleTime constant τ

1 s

10 kΩ and 100 µF charge to 63.2% of 9 V (5.689 V) in one time constant, 1 s, and are practically full (99.3%) after 5τ, 5 s.

Type your own R and C to see your time constant.

1τ2τ86.5%3τ95%4τ5τ9 V05.689 V at ττ = 1 s
Full (99.3%) after 5τ
5 s
Current at the start
900 µA
Charge when full
900 µC
How this works: 6 sources,

How this works

Method

The time constant is τ = R × C. Charging toward a voltage follows v = Vend + (Vstart − Vend) × e^(−t/τ), solved for t (or for R, given a delay). Stored energy is ½CV² and charge CV. A first-order RC filter cuts off at 1 ÷ (2πRC), with gain 1 ÷ √(1 + (f/fc)²). Capacitor codes give picofarads as two digits and a power of ten, with IEC 60062 tolerance letters.

How it’s tested

14 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: the RC time constant with its curve, plus charge time, energy, RC filter cutoff and capacitor code pages.

Every change on What’s new

How we make toolsReport a mistake

Key facts

  • The time constant of a resistor and capacitor is τ = R × C: 10 kΩ × 100 µF = 1 s.
  • After one time constant a charging capacitor is at 63.2% of the supply; after five, 99.3%.
  • In OpenStax’s Example 10.8, 101 Ω and 50 mF give τ = 5.05 s.

Source: OpenStax University Physics Volume 2, §10.5 RC Circuits

All 4 calculators

Time and energy · Filters and codes

The charging curve

Charge after each time constant
AfterCharging: reachedDischarging: left
1 τ63.2%36.8%
2 τ86.5%13.5%
3 τ95.0%5.0%
4 τ98.2%1.8%
5 τ99.3%0.7%

Through a resistor, current into a capacitor is largest at the start and shrinks as the capacitor fills, because the voltage left across the resistor shrinks. That gives the exponential curve on the card, the same shape for every R, C and voltage, stretched by τ. Discharging is the same curve upside down.

Engineers use it everywhere: power-on reset delays, debouncing a switch, timers and flashing lights, smoothing a supply and the simplest filters. The pages below work out the time to a voltage, the energy stored, the filter cutoff and how to read the code on the part.

Sources

Common questions

What is the RC time constant?

τ = R × C, in seconds when R is in ohms and C in farads. It is the time a capacitor charging through a resistor takes to cover 63.2% of the way to the supply voltage, or discharging, to fall to 36.8%. 10 kΩ and 100 µF give τ = 1 s.

How long until a capacitor is fully charged?

In theory never; in practice five time constants, when it is within 0.7% of the supply. With 10 kΩ and 100 µF that is 5 seconds.

Why 63.2%?

The charging curve is 1 − e^(−t/τ). At t = τ that is 1 − 1/e = 0.632. Each further time constant covers 63.2% of what is left: 86.5% after 2τ, 95.0% after 3τ.

Does the voltage change the time constant?

No. τ depends only on R and C. The voltage sets where the curve ends, and the current at the start (V ÷ R), not how fast it gets there in proportion.