Ohm's Law Calculator
Type any two of volts, amps, ohms and watts. The other two appear, with the working.
Type any two of voltage, current, resistance and power to get the other two, with a live circuit, the formulas used and the working. Watts to amps, kVA and three phase too.
Type any two values; the other two are worked out. A third value replaces the older of the two.
ExampleCurrent
2A
12 V across 6 Ω drives 2 A and turns 24 W into heat.
Type any two values to work out the other two.
The dots speed up with more current; the resistor glows brighter with more power.
- Power
- 24 W
- Energy in an hour
- 24 Wh
- Formulas
- I = V ÷ R · P = V² ÷ R
Circuit physics for learning and planning, not wiring advice: installations must follow your local electrical code and a qualified electrician. Terms
How this works: 8 sources,
How this works
Method
Ohm’s law (V = I × R) and the power law (P = V × I) give the two quantities you didn’t type from the two you did, using the twelve rearranged formulas. AC power uses P = V × I × PF on one phase and P = √3 × V × I × PF on three phases with the line-to-line voltage; apparent power leaves out the power factor, and power factor correction is Qc = P × (tan φ1 − tan φ2).
Sources
- University Physics Volume 2, §9.4 Ohm’s Law (OpenStax (Ling, Sanny and Moebs), 2016)
- University Physics Volume 2, §9.5 Electrical Energy and Power (OpenStax (Ling, Sanny and Moebs), 2016)
- University Physics Volume 2, §15.4 Power in an AC Circuit (OpenStax (Ling, Sanny and Moebs), 2016)
- The International System of Units (SI Brochure), 9th edition (BIPM, 2019)
- IEEE Std 1459-2010, Definitions for the Measurement of Electric Power Quantities (IEEE, 2010)
- AC Electrical Circuit Analysis, §9.3 Three-Phase Connections (James M. Fiore, LibreTexts)
- AC Electrical Circuit Analysis, §9.4 Power Factor Correction (James M. Fiore, LibreTexts)
- IEC 60038:2009+AMD1:2021, IEC standard voltages (IEC, 2009)
How it’s tested
21 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
Circuit physics for learning and planning, not wiring advice: installations must follow your local electrical code and a qualified electrician.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: Ohm’s law from any two values with a live circuit and the formula wheel, plus watts to amps, amps to watts, kW and kVA to amps, three-phase power and power factor pages.
Key facts
- Ohm’s law: current = voltage ÷ resistance, so 12 V across 6 Ω drives 2 A and the resistor dissipates 24 W.
- A 9.00 V battery driving 3.00 mA through a carbon resistor means it has 3.00 kΩ of resistance (OpenStax Example 9.8).
- The SI defines the ohm as one volt per ampere and the watt as one joule per second.
Sources: OpenStax University Physics Volume 2, §9.4 and §9.5; BIPM SI Brochure, 9th edition
All 6 calculators
Watts, amps and kVA · AC power
The twelve formulas
Ohm’s law (V = I × R) and the power law (P = V × I), rearranged for each quantity.
| To find | From V, I or R | From P and one | From the other pair |
|---|---|---|---|
| Voltage (V) | I × R | P ÷ I | √(P × R) |
| Current (I) | V ÷ R | P ÷ V | √(P ÷ R) |
| Resistance (R) | V ÷ I | V² ÷ P | P ÷ I² |
| Power (P) | V × I | I² × R | V² ÷ R |
Every formula comes from two facts. Voltage is current times resistance: a 6 Ω resistor with 2 A through it has 12 V across it. Power is voltage times current: those 12 V and 2 A deliver 24 W. Substitute one into the other and you get the rest, such as P = I² × R, which is why the heat in a cable grows with the square of the current.
The units multiply the same way. One volt is one watt per ampere, and one ohm is one volt per ampere, so the answer comes out in base units when you put base units in. The calculator takes millivolts to kilovolts, microamps to amps, ohms to megohms and milliwatts to kilowatts and does the scaling for you.
When the simple formulas aren’t enough
- Resistance changes with temperature: copper’s rises about 0.4% per °C, and a lamp filament’s is several times higher hot than cold.
- AC loads with motors or electronics have a power factor below 1, so watts are less than volts times amps. Use the watts to amps or power factor pages.
- Diodes and LEDs have a nearly fixed voltage, not a resistance; size their series resistor from the voltage left over.
- Real batteries have internal resistance, so their voltage drops under load.
Sources
- OpenStax (Ling, Sanny and Moebs), University Physics Volume 2, §9.4 Ohm’s Law
- OpenStax (Ling, Sanny and Moebs), University Physics Volume 2, §9.5 Electrical Energy and Power
- OpenStax (Ling, Sanny and Moebs), University Physics Volume 2, §15.4 Power in an AC Circuit
- BIPM, The International System of Units (SI Brochure), 9th edition
- IEEE, IEEE Std 1459-2010, Definitions for the Measurement of Electric Power Quantities
- James M. Fiore, LibreTexts, AC Electrical Circuit Analysis, §9.3 Three-Phase Connections
- James M. Fiore, LibreTexts, AC Electrical Circuit Analysis, §9.4 Power Factor Correction
- IEC, IEC 60038:2009+AMD1:2021, IEC standard voltages
Common questions
What is Ohm’s law?
The current through a resistor is the voltage across it divided by its resistance: I = V ÷ R, usually written V = I × R. Georg Ohm published it in 1827. With the power formula P = V × I it gives twelve ways to work out volts, amps, ohms or watts from any two of them.
How do I use the calculator?
Type any two of voltage, current, resistance and power, in whichever units you have (mA, kΩ, kW). The other two are worked out at once and shown in their fields. Type in a third field and the calculator lets go of the older of the two you typed.
Does Ohm’s law work for AC?
For resistive loads such as heaters and filament lamps, yes, with rms voltages and currents. Motors, transformers and electronics add reactance and a power factor, so watts are no longer simply volts times amps; the watts to amps and power factor pages handle that.
Does every component obey Ohm’s law?
No. Resistors and metal wires at a steady temperature do: their resistance stays the same as the voltage changes. Diodes, LEDs and transistors don’t, and a lamp filament’s resistance rises as it heats up. Use the resistance at the operating point for those.
Why does the power go up so fast with voltage?
Because power is V² ÷ R for a fixed resistance: double the voltage and the current doubles too, so the power goes up four times. A 6 Ω resistor takes 24 W at 12 V and 96 W at 24 V.