Skip to content

Capacitor Charge Time Calculator

The time an RC circuit takes to reach a voltage, charging or discharging…

The time an RC circuit takes to reach a voltage, charging or discharging, or the resistor for a delay you need, such as a timer or a soft start.

Ω
F
V
V
V

To discharge, make the end lower than the start (0 V for a resistor across the capacitor).

ExampleTime to 10 V

1.792 s

1 kΩ and 1 mF take 1.792 s to charge from 0 V to 10 V, heading for 12 V: 1.79 time constants.

Enter your own circuit to see your time.

1τ63.2%2τ3τ95%4τ5τ12 V010 V at 1.792 sτ = 1 s
Time constant τ
1 s
In time constants
1.79 τ
To 99.3% of the way
5 s
How this works: 6 sources,

How this works

Method

Through a resistor, a capacitor’s voltage moves toward the supply quickly at first and then ever more slowly, on an exponential curve with time constant τ = R × C. After one τ it has covered 63.2% of the way, after two 86.5%, after three 95.0%, and after five 99.3%, which is why "five time constants" is the usual answer to "how long until it’s charged". Full method

How it’s tested

3 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: the RC time constant with its curve, plus charge time, energy, RC filter cutoff and capacitor code pages.

Every change on What’s new

How we make toolsReport a mistake

How long a capacitor takes to charge

Through a resistor, a capacitor’s voltage moves toward the supply quickly at first and then ever more slowly, on an exponential curve with time constant τ = R × C. After one τ it has covered 63.2% of the way, after two 86.5%, after three 95.0%, and after five 99.3%, which is why "five time constants" is the usual answer to "how long until it’s charged".

To reach a particular voltage, solve the curve for time: t = τ × ln((Vend − Vstart) ÷ (Vend − v)). Charging 1,000 µF through 1 kΩ (τ = 1 s) from 0 toward 12 V reaches 10 V after ln(12 ÷ 2) = 1.79 τ, or 1.79 s. Discharging works the same way toward 0 V.

Turned around, the formula gives the resistor for a delay, the idea behind RC timers and the intermittent windshield wiper in OpenStax’s Example 10.9: 10.00 mF reaching 10 V of a 12 V supply in 10.00 s needs 558 Ω. Real capacitors have tolerances of 10 to 20% and some leakage, so a precise timer uses a timer chip with the RC network.

τ = R × C · v(t) = Vend + (Vstart − Vend) × e^(−t/τ) · t = τ × ln((Vend − Vstart) ÷ (Vend − v))

Share of the way after each time constant

Charging from 0 toward the supply (discharging is the mirror image), and the time for 1 kΩ with 1,000 µF (τ = 1 s).

Charging from 0 toward the supply (discharging is the mirror image), and the time for 1 kΩ with 1,000 µF (τ = 1 s).
TimeChargedLeft to goWith τ = 1 s
0.5 τ39.3%60.7%500 ms
0.69 τ49.8%50.2%690 ms
1 τ63.2%36.8%1 s
1.5 τ77.7%22.3%1.5 s
2 τ86.5%13.5%2 s
2.3 τ90%10%2.3 s
3 τ95%4.98%3 s
4 τ98.2%1.83%4 s
4.6 τ99%1.01%4.6 s
5 τ99.3%0.674%5 s
Show all 11 rows
7 τ99.9%0.0912%7 s

Common questions

Why does a capacitor never quite finish charging?

The current through the resistor is proportional to the voltage still left to go, so the closer it gets, the slower it charges. In theory it never arrives; in practice after 5τ it is within 0.7%, below most measurements.

Is discharging faster than charging?

Through the same resistance, no: both follow the same time constant. A circuit often discharges through a different path, though, so its discharge time constant can be very different.

How long does half-charge take?

ln 2 = 0.693 time constants. With 10 kΩ and 100 µF (τ = 1 s), that is 0.69 s.