Skip to content

Capacitors in Series and Parallel Calculator

Capacitors combine the opposite way to resistors: in parallel they add…

Capacitors combine the opposite way to resistors: in parallel they add, in series the total is smaller than the smallest. Switch between the two.

Capacitors
F
F

Type 100p, 47n, 10µ (or 10u).

Reach a target valueWhat to add to get a value you can’t buy

Type the total you want, such as 150 or 2.2k.

ExampleTotal capacitance

6.875µF

10 µF and 22 µF in series make 6.875 µF, less than the smallest of them.

Type your own values to see your total.

10 µF22 µF

Bars: each capacitor’s share of the voltage; the smallest takes the most.

In parallel instead
32 µF
How this works: 8 sources,

How this works

Method

Capacitors work the opposite way to resistors. In parallel they add, because the plates together hold more charge at the same voltage: 10 µF and 22 µF make 32 µF. In series the reciprocals add, so the total is smaller than the smallest: 1 ÷ (1/10 + 1/22) = 6.875 µF. Full method

How it’s tested

3 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: the colour code on a resistor you can tap, with series and parallel, capacitors, voltage divider, LED resistor, SMD code and standard value pages.

Every change on What’s new

How we make toolsReport a mistake

How capacitors combine

Capacitors work the opposite way to resistors. In parallel they add, because the plates together hold more charge at the same voltage: 10 µF and 22 µF make 32 µF. In series the reciprocals add, so the total is smaller than the smallest: 1 ÷ (1/10 + 1/22) = 6.875 µF.

Capacitors in series all hold the same charge, so the voltage splits in inverse proportion to their capacitance: the smallest capacitor takes the largest share of the voltage. That matters when you stack capacitors to raise a voltage rating; makers add balancing resistors because real parts leak unevenly.

Units matter more here than with resistors: values run from picofarads to farads. 1 µF = 1,000 nF = 1,000,000 pF. Type them as printed, such as 100n, 4.7µ or 22p, and the calculator keeps track.

Parallel: C = C₁ + C₂ + … · series: 1/C = 1/C₁ + 1/C₂ + …

Two capacitors, series and parallel

Totals for common pairs, worked out by the calculator’s own code.

Totals for common pairs, worked out by the calculator’s own code.
C₁C₂In seriesIn parallel
22 pF22 pF11 pF44 pF
100 pF220 pF68.75 pF320 pF
1 nF1 nF500 pF2 nF
10 nF100 nF9.091 nF110 nF
100 nF100 nF50 nF200 nF
100 nF1 µF90.91 nF1.1 µF
1 µF1 µF500 nF2 µF
1 µF4.7 µF824.6 nF5.7 µF
10 µF22 µF6.875 µF32 µF
47 µF47 µF23.5 µF94 µF
Show all 12 rows
100 µF220 µF68.75 µF320 µF
470 µF1 mF319.7 µF1.47 mF

Common questions

Why do capacitors add in parallel but resistors add in series?

Capacitance measures how much charge a part stores per volt. In parallel the plates act as one bigger plate, so charge storage adds. Resistance measures opposition to current, which adds along a single path.

What happens to the voltage rating in series?

Two equal capacitors in series can take about twice the voltage, since each gets half. With unequal values the smaller one takes more, and real leakage makes the split uneven, so high-voltage stacks use balancing resistors.

How do I read 104 on a ceramic capacitor?

Like an SMD resistor code, in picofarads: 10 followed by 4 zeros is 100,000 pF, which is 100 nF or 0.1 µF. 103 is 10 nF and 472 is 4.7 nF.