RC Filter Cutoff Frequency Calculator
Where a resistor and capacitor filter starts to cut: the −3 dB frequency…
Where a resistor and capacitor filter starts to cut: the −3 dB frequency, and what it does to any frequency you pick, low-pass or high-pass.
ExampleCutoff (−3 dB)
1.592kHz
1 kΩ and 100 nF make a low-pass filter with its −3 dB cutoff at 1.592 kHz; at 10 kHz it passes 15.7% of the voltage (-16.1 dB).
Type your own R and C to see your cutoff.
- At 10 kHz
- -16.1 dB, -81°
- Time constant
- 100 µs
- Roll-off
- −20 dB per decade (−6 dB per octave)
How this works: 6 sources,
How this works
Method
A resistor and capacitor make the simplest filter. The capacitor’s opposition to AC, its reactance 1 ÷ (2πfC), falls as frequency rises, so in a low-pass filter (output across the capacitor) high frequencies are shorted away. The cutoff fc is where the reactance equals the resistance: fc = 1 ÷ (2πRC). With 1 kΩ and 100 nF that is 1,592 Hz. Full method
Sources
- University Physics Volume 2, §15.2 Simple AC Circuits (capacitive reactance) (OpenStax (Ling, Sanny and Moebs), 2016)
- University Physics Volume 2, §10.5 RC Circuits (OpenStax (Ling, Sanny and Moebs), 2016)
- University Physics Volume 2, §8.3 Energy Stored in a Capacitor (OpenStax (Ling, Sanny and Moebs), 2016)
- University Physics Volume 2, §8.2 Capacitors in Series and in Parallel (OpenStax (Ling, Sanny and Moebs), 2016)
- IEC 60062:2016+AMD1:2019, Marking codes for resistors and capacitors (IEC, 2016)
- Capacitor: three- and four-character marking code (Wikipedia)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: the RC time constant with its curve, plus charge time, energy, RC filter cutoff and capacitor code pages.
How an RC filter’s cutoff is found
A resistor and capacitor make the simplest filter. The capacitor’s opposition to AC, its reactance 1 ÷ (2πfC), falls as frequency rises, so in a low-pass filter (output across the capacitor) high frequencies are shorted away. The cutoff fc is where the reactance equals the resistance: fc = 1 ÷ (2πRC). With 1 kΩ and 100 nF that is 1,592 Hz.
At the cutoff the output is 1 ÷ √2, 70.7% of the input voltage, which is −3 dB, and lags by 45°. Above it the gain falls by 20 dB for every tenfold rise in frequency: at 10 kHz the same filter passes 15.7% (−16.1 dB). Swap the parts (output across the resistor) for a high-pass with the same cutoff.
The formula assumes a source with no resistance of its own and a load that draws nothing. A load in parallel with the output, or a source resistance in series, shifts the cutoff; buffer the filter or include them in R.
fc = 1 ÷ (2π R C) · low-pass gain = 1 ÷ √(1 + (f/fc)²) · phase = −atan(f/fc)
- A capacitor’s reactance is X = 1 ÷ (2πfC), so it passes high frequencies and blocks low ones. Source: University Physics Volume 2, §15.2 Simple AC Circuits (capacitive reactance).
- An RC circuit’s time constant τ = RC also sets the filter: fc = 1 ÷ (2πτ). Source: University Physics Volume 2, §10.5 RC Circuits.
Cutoff frequencies for common R and C
fc = 1 ÷ (2πRC), worked out by the calculator’s own code, and the gain one decade above it.
| R | C | Cutoff | At 10 × fc |
|---|---|---|---|
| 100 Ω | 1 µF | 1.592 kHz | -20 dB |
| 1 kΩ | 1 µF | 159.2 Hz | -20 dB |
| 1 kΩ | 100 nF | 1.592 kHz | -20 dB |
| 1 kΩ | 10 nF | 15.92 kHz | -20 dB |
| 10 kΩ | 10 nF | 1.592 kHz | -20 dB |
| 10 kΩ | 1 nF | 15.92 kHz | -20 dB |
| 4.7 kΩ | 100 nF | 338.6 Hz | -20 dB |
| 10 kΩ | 100 nF | 159.2 Hz | -20 dB |
| 100 kΩ | 100 nF | 15.92 Hz | -20 dB |
| 1 kΩ | 470 pF | 338.6 kHz | -20 dB |
Show all 11 rowsShow fewer
| 10 kΩ | 1 µF | 15.92 Hz | -20 dB |
Common questions
What does −3 dB mean?
The output voltage is 70.7% of the input, so the output power is half. It is the conventional edge of a filter’s passband.
How do I get a steeper filter?
Cascade stages: two RC stages give −40 dB per decade, though passive stages load each other, so active filters with op-amps are common for sharper cutoffs.
Can I use this for a high-pass filter?
Yes. Switch to high-pass: the same R and C give the same cutoff, with the output taken across the resistor so it passes frequencies above fc.