Deck Board Calculator
Deck boards for your deck, laid row by row with the gaps the maker asks for and…
Deck boards for your deck, laid row by row with the gaps the maker asks for and every joint on a joist, and the screws to fix them.
Boards run along the length.
ExampleBoards to buy
33boards of 16′
26 rows over 16 joists, every joint on a joist.
Enter yours to see your result.
- Screws, 2 a joist
- 884
- Left over
- 8′
- Deck
- 240 sq ft
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
How this works: 19 sources,
How this works
Method
Deck boards run in rows across the joists, each row one board wide plus the gap the maker asks for. The rows are the deck’s width ÷ (board + gap), rounded up. Along each row the boards have to join over a joist, so a row longer than a board is split at joist positions, and alternate rows split on different joists so the joints stagger. The pieces are then packed into the board lengths you buy. Full method
Sources
- Decking Installation Guide (Trex)
- Deck construction guidelines based on IRC Table R507.7 (Johnson County, Kansas) (Johnson County, Kansas, 2018)
- Emerald Interior Acrylic Latex product data sheet (Sherwin-Williams, 2023)
- BEHR PREMIUM PLUS Interior Eggshell Enamel No. 2050 technical data sheet (Behr, revised 9/2019)
- Dulux Trade Vinyl Matt data sheet 411 (AkzoNobel, 2025)
- Sheetrock Installation and Finish Guide (fastener, compound and tape calculator) (USG, 2003)
- Sheetrock UltraLight panels submittal sheet (sizes) (USG, 2010)
- Ultraflex 2 product data sheet (MAPEI, 2024)
- VersaBond Professional Tile Mortar, TDS-119 (Custom Building Products, 2026)
- Polyblend Plus Sanded Grout, TDS-360 (coverage chart) (Custom Building Products, 2026)
- Installation Essentials Guide for Laminate Flooring (Pergo)
- CRI 105, Standard for Installation of Residential Carpet (The Carpet and Rug Institute, 2019)
- Roofing Collection Product Guide (bundles, starter, hip and ridge, underlayment) (Owens Corning)
- Interlocking concrete pavement guide specification (PAV-TEC-009-13) (Interlocking Concrete Pavement Institute / CMHA, 2013)
- HP NextGel polymeric sand data sheet (Techniseal, 2023)
- Technical Note 10, Dimensioning and Estimating Brick Masonry (Brick Industry Association, 2009)
- Calculating wallpaper quantities (Farrow & Ball)
- Primed MDF baseboard mouldings (lengths) (Metrie)
- NIST Handbook 44 (2026), Appendix C: General tables of units of measurement (National Institute of Standards and Technology, 2026)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: square footage of any rooms you draw, with paint, tile, drywall, flooring, carpet, roofing, pavers, brick, wallpaper, baseboard and deck board pages.
How the deck boards are worked out
Deck boards run in rows across the joists, each row one board wide plus the gap the maker asks for. The rows are the deck’s width ÷ (board + gap), rounded up. Along each row the boards have to join over a joist, so a row longer than a board is split at joist positions, and alternate rows split on different joists so the joints stagger. The pieces are then packed into the board lengths you buy.
For a 16 × 12 ft deck in 16 ft boards on joists 12 inches apart: 26 rows, each one whole board, 26 boards and 884 screws at two per board per joist (two more at each butt joint, where two boards end on the same joist). Trex asks for joists no more than 16 inches apart for its residential boards, and 4 inches closer when the boards run at 45°.
Trex’s guide also gives the gaps: at least 3/16 inch between boards side to side, ⅛ inch at butt ends above 40°F, and up to ½ inch where a board meets a house or post. For wood decking, the IRC deck tables allow joists up to 16 inches apart for 1¼ inch boards laid square.
rows = ⌈ width ÷ (board + gap) ⌉; screws = rows × joists × 2
- Minimum side-to-side gap 3/16 in; 1 in boards on 16 in joists for residential decks, 4 in less at 45°; two screws per joist. Source: Decking Installation Guide.
- Wood decking 1¼ in thick: joists at most 16 in apart laid square, 12 in diagonally (IRC Table R507.7). Source: Deck construction guidelines based on IRC Table R507.7 (Johnson County, Kansas).
Deck boards for common deck sizes
5½ in boards, 3/16 in gaps, joists 16 in apart.
| Deck | Rows | 16 ft boards | 12 ft boards | Screws |
|---|---|---|---|---|
| 12 × 10 ft | 22 | 22 | 22 | 440 |
| 16 × 12 ft | 26 | 26 | 39 | 676 |
| 20 × 12 ft | 26 | 33 | 52 | 884 |
| 16 × 16 ft | 34 | 34 | 51 | 884 |
| 24 × 16 ft | 34 | 51 | 68 | 1,360 |
| 20 × 20 ft | 43 | 54 | 86 | 1,462 |
Sources
- Trex, Decking Installation Guide
- Johnson County, Kansas, Deck construction guidelines based on IRC Table R507.7 (Johnson County, Kansas)
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
How many deck boards do I need?
Divide the deck’s width by a board plus its gap for the rows, then see how each row cuts from the board length you buy. A 16 × 12 ft deck in 5½ in boards with 3/16 in gaps is 26 rows of 16 ft boards, 26 boards.
What gap do deck boards need?
Trex asks for at least 3/16 inch between boards side to side, ⅛ inch at the ends above 40°F (3/16 below), and ¼ to ½ inch against the house. Wood decking makers give their own gaps; hidden fasteners often set the gap for you.
How many screws for a deck?
Two per board at every joist it crosses, which is Trex’s rule for face screws and the IRC’s minimum for wood decking. A 16 × 12 ft deck on 16 in joists has 13 joists, so 26 rows × 13 × 2 = 676 screws.