Baseboard Calculator
Baseboard for a room, the walls less the doorways, and how many lengths to buy…
Baseboard for a room, the walls less the doorways, and how many lengths to buy, with the cut list that gets them out of the fewest boards.
Doorways
ExampleLengths to buy
4× 16′
46′ of baseboard round 4 walls, less 2 doorways.
Enter yours to see your result.
- Left over
- 18′
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
How this works: 18 sources,
How this works
Method
Baseboard runs round the walls, less the doorways. The calculator takes each wall of your room, takes a doorway’s width off one wall per doorway, and then packs the runs into the lengths sold, longest first, using an offcut on a shorter wall before starting a new length. That gives the lengths to buy and a cut list, rather than total feet divided by the length, which ignores that offcuts are often too short to use. Full method
Sources
- Primed MDF baseboard mouldings (lengths) (Metrie)
- Emerald Interior Acrylic Latex product data sheet (Sherwin-Williams, 2023)
- BEHR PREMIUM PLUS Interior Eggshell Enamel No. 2050 technical data sheet (Behr, revised 9/2019)
- Dulux Trade Vinyl Matt data sheet 411 (AkzoNobel, 2025)
- Sheetrock Installation and Finish Guide (fastener, compound and tape calculator) (USG, 2003)
- Sheetrock UltraLight panels submittal sheet (sizes) (USG, 2010)
- Ultraflex 2 product data sheet (MAPEI, 2024)
- VersaBond Professional Tile Mortar, TDS-119 (Custom Building Products, 2026)
- Polyblend Plus Sanded Grout, TDS-360 (coverage chart) (Custom Building Products, 2026)
- Installation Essentials Guide for Laminate Flooring (Pergo)
- CRI 105, Standard for Installation of Residential Carpet (The Carpet and Rug Institute, 2019)
- Roofing Collection Product Guide (bundles, starter, hip and ridge, underlayment) (Owens Corning)
- Interlocking concrete pavement guide specification (PAV-TEC-009-13) (Interlocking Concrete Pavement Institute / CMHA, 2013)
- HP NextGel polymeric sand data sheet (Techniseal, 2023)
- Technical Note 10, Dimensioning and Estimating Brick Masonry (Brick Industry Association, 2009)
- Calculating wallpaper quantities (Farrow & Ball)
- Decking Installation Guide (Trex)
- NIST Handbook 44 (2026), Appendix C: General tables of units of measurement (National Institute of Standards and Technology, 2026)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: square footage of any rooms you draw, with paint, tile, drywall, flooring, carpet, roofing, pavers, brick, wallpaper, baseboard and deck board pages.
How the baseboard is worked out
Baseboard runs round the walls, less the doorways. The calculator takes each wall of your room, takes a doorway’s width off one wall per doorway, and then packs the runs into the lengths sold, longest first, using an offcut on a shorter wall before starting a new length. That gives the lengths to buy and a cut list, rather than total feet divided by the length, which ignores that offcuts are often too short to use.
For a 16 × 13 ft room with one 3 ft doorway, from 12 ft lengths: runs of 13, 13, 16 and 10 ft. The two 16 and 13 ft walls each need a joint, so the pieces pack into 5 lengths with 5.0 ft left over. Longer stock, if your store has it, means fewer joints.
Metrie’s primed MDF baseboard comes in 10, 12, 14 and 16 ft lengths, depending on the profile. Corners need mitred or coped joints, which take a little length each; the leftover in the cut list usually covers them, and long walls are joined with a scarf joint over a stud.
lengths = runs (walls − doorways), split at the stock length, packed first-fit decreasing
- Primed MDF baseboard profiles come in 10, 12, 14 and 16 ft lengths. Source: Primed MDF baseboard mouldings (lengths).
Baseboard for common rooms
One 3 ft doorway; lengths from the cut list.
| Room | Baseboard | 12 ft lengths | 16 ft lengths |
|---|---|---|---|
| 10 × 10 ft | 37 ft | 4 | 4 |
| 12 × 10 ft | 41 ft | 4 | 4 |
| 12 × 12 ft | 45 ft | 4 | 4 |
| 14 × 12 ft | 49 ft | 5 | 4 |
| 16 × 14 ft | 57 ft | 5 | 4 |
| 20 × 16 ft | 69 ft | 6 | 5 |
Sources
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
How do I calculate baseboard?
Add up the length of every wall and take off the doorways: a 12 × 12 ft room with one 3 ft door needs 45 ft. Then work out how the walls cut from the lengths you buy; the calculator does this and shows each length’s cuts.
How much extra baseboard should I buy?
The cut list already counts whole lengths, including offcuts that can’t be used. Some people buy one spare length for a miscut, especially with expensive profiles.
Do closets count?
Yes, if they get baseboard. Add the closet as its own shape so its walls are counted, and add its doorway.