Tile Calculator
The floor laid tile by tile in the pattern you pick…
The floor laid tile by tile in the pattern you pick, so the count is the tiles you will really cut, with thin slivers flagged and the start point yours to move.
Joint
Pattern
More options¼ × ¼ in square trowel · 0% spare
Trowel notch
Spares on top
The count already includes every cut piece. Spares cover breakage and a later repair.
ExampleTiles to buy
80tiles
48 whole and 32 cut.
Enter yours to see your result.
- Thinset, 50 lb bags
- 2
- Sanded grout
- 5.8 lb
- Floor
- 80 sq ft
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
How this works: 18 sources,
How this works
Method
Most tile calculators divide the floor area by a tile’s area and add a percentage for waste. This one lays the floor: it places every tile in your pattern from the start point, clips each one at the walls, and counts the pieces. A whole tile is one tile; every cut piece also uses a tile, because offcuts rarely fit elsewhere. So the count already includes the cuts, and the narrowest cut is measured, so you can see a thin sliver before you lay it. Full method
Sources
- Ultraflex 2 product data sheet (MAPEI, 2024)
- VersaBond Professional Tile Mortar, TDS-119 (Custom Building Products, 2026)
- Polyblend Plus Sanded Grout, TDS-360 (coverage chart) (Custom Building Products, 2026)
- Emerald Interior Acrylic Latex product data sheet (Sherwin-Williams, 2023)
- BEHR PREMIUM PLUS Interior Eggshell Enamel No. 2050 technical data sheet (Behr, revised 9/2019)
- Dulux Trade Vinyl Matt data sheet 411 (AkzoNobel, 2025)
- Sheetrock Installation and Finish Guide (fastener, compound and tape calculator) (USG, 2003)
- Sheetrock UltraLight panels submittal sheet (sizes) (USG, 2010)
- Installation Essentials Guide for Laminate Flooring (Pergo)
- CRI 105, Standard for Installation of Residential Carpet (The Carpet and Rug Institute, 2019)
- Roofing Collection Product Guide (bundles, starter, hip and ridge, underlayment) (Owens Corning)
- Interlocking concrete pavement guide specification (PAV-TEC-009-13) (Interlocking Concrete Pavement Institute / CMHA, 2013)
- HP NextGel polymeric sand data sheet (Techniseal, 2023)
- Technical Note 10, Dimensioning and Estimating Brick Masonry (Brick Industry Association, 2009)
- Calculating wallpaper quantities (Farrow & Ball)
- Primed MDF baseboard mouldings (lengths) (Metrie)
- Decking Installation Guide (Trex)
- NIST Handbook 44 (2026), Appendix C: General tables of units of measurement (National Institute of Standards and Technology, 2026)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: square footage of any rooms you draw, with paint, tile, drywall, flooring, carpet, roofing, pavers, brick, wallpaper, baseboard and deck board pages.
How the tiles are worked out
Most tile calculators divide the floor area by a tile’s area and add a percentage for waste. This one lays the floor: it places every tile in your pattern from the start point, clips each one at the walls, and counts the pieces. A whole tile is one tile; every cut piece also uses a tile, because offcuts rarely fit elsewhere. So the count already includes the cuts, and the narrowest cut is measured, so you can see a thin sliver before you lay it.
Take a 7 × 5 ft bathroom floor in 12 × 24 in tiles with ⅛ in joints, laid in a half offset from one corner. The layout has 12 whole tiles and 10 cut pieces: 22 tiles, where 35 sq ft ÷ 2 sq ft would suggest 18. Moving the start point changes both numbers, which is why the handle is on the drawing.
Centring the layout, the calculator’s default, gives equal cuts at opposite walls. Herringbone and diagonal layouts cut more tiles at the edges, and the count shows exactly how many. Thinset is worked out from the bag maker’s coverage for your trowel notch, and grout from the joint volume, using Custom Building Products’ chart.
tiles = whole tiles + cut pieces (from the layout); grout = joint length × width × depth × density
- A 50 lb bag of Ultraflex 2 covers 75 to 90 sq ft with a ¼ × ¼ in square notch, 55 to 65 with ¼ × ⅜. Source: Ultraflex 2 product data sheet.
- VersaBond Professional covers 90 to 100 sq ft a bag at ¼ × ¼ in, and 42 to 47 at ½ × ½ in. Source: VersaBond Professional Tile Mortar, TDS-119.
- A 25 lb bag of Polyblend Plus sanded grout covers 348 sq ft of 12 × 12 × ⅜ in tile at ⅛ in joints. Source: Polyblend Plus Sanded Grout, TDS-360 (coverage chart).
Tiles and grout per 100 square feet
By area with ⅛ in joints, before cuts; grout for ⅜ in thick tile. The layout above counts cuts exactly.
| Tile | Tiles per 100 sq ft | Grout per 100 sq ft |
|---|---|---|
| 4 × 4 in | 847 | 21.6 lb |
| 6 × 6 in | 384 | 14.4 lb |
| 12 × 12 in | 98 | 7.2 lb |
| 12 × 24 in | 50 | 5.4 lb |
| 18 × 18 in | 44 | 4.8 lb |
| 24 × 24 in | 25 | 3.6 lb |
| 3 × 12 in | 381 | 18.0 lb |
| 6 × 24 in | 98 | 9.0 lb |
Sources
- MAPEI, Ultraflex 2 product data sheet
- Custom Building Products, VersaBond Professional Tile Mortar, TDS-119
- Custom Building Products, Polyblend Plus Sanded Grout, TDS-360 (coverage chart)
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
How many tiles do I need?
Lay the floor out tile by tile and count the pieces, as this page does: every cut uses a tile. As a rough check, divide the floor area by one tile with its joint: 100 sq ft of 12 × 12 in tile with ⅛ in joints is 98 tiles before any cuts.
How much extra tile should I buy?
The count here already includes every cut piece, so the extra is only for breakage and repairs. Many people keep a few spares from the same batch, because colours vary between production runs. Set a spare percentage under More options if you want one.
What is a sliver, and how do I avoid one?
A cut piece so narrow it is hard to cut cleanly and looks wrong against a wall. The layout flags cuts under 2 inches (5 cm). Drag the start point, or tap the centre, until the cuts at both walls are wider.
How much thinset and grout?
Thinset depends on the trowel notch: MAPEI gives 75 to 90 sq ft per 50 lb bag for a ¼ × ¼ in notch, so the calculator uses the lower figure. Grout depends on the joint width, the tile’s thickness and size; it is worked out from the joint volume, at a density taken from Custom’s chart.