Carpet Calculator
Carpet is cut from a roll in drops as wide as the roll…
Carpet is cut from a roll in drops as wide as the roll, so this shows the square yards you pay for, the seams and the direction that wastes least.
ExampleCarpet to buy
20square yards
1 drop of 15′ off a 12′ roll, 0 seams.
Enter yours to see your result.
- Floor
- 20 sq yd
- The other way round
- 32 sq yd
- Off the roll
- 15′
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
How this works: 18 sources,
How this works
Method
Carpet is cut from a roll of a fixed width, so a room takes whole widths, called drops, each as long as the room. A 15 × 12 ft room from a 12 ft roll is one drop 15 ft long: 180 sq ft, 20 square yards, with no seam. Turned the other way it would be two drops of 12 ft, with a seam and 288 sq ft of carpet. The calculator works out both directions and shows the one that uses less. Full method
Sources
- CRI 105, Standard for Installation of Residential Carpet (The Carpet and Rug Institute, 2019)
- Emerald Interior Acrylic Latex product data sheet (Sherwin-Williams, 2023)
- BEHR PREMIUM PLUS Interior Eggshell Enamel No. 2050 technical data sheet (Behr, revised 9/2019)
- Dulux Trade Vinyl Matt data sheet 411 (AkzoNobel, 2025)
- Sheetrock Installation and Finish Guide (fastener, compound and tape calculator) (USG, 2003)
- Sheetrock UltraLight panels submittal sheet (sizes) (USG, 2010)
- Ultraflex 2 product data sheet (MAPEI, 2024)
- VersaBond Professional Tile Mortar, TDS-119 (Custom Building Products, 2026)
- Polyblend Plus Sanded Grout, TDS-360 (coverage chart) (Custom Building Products, 2026)
- Installation Essentials Guide for Laminate Flooring (Pergo)
- Roofing Collection Product Guide (bundles, starter, hip and ridge, underlayment) (Owens Corning)
- Interlocking concrete pavement guide specification (PAV-TEC-009-13) (Interlocking Concrete Pavement Institute / CMHA, 2013)
- HP NextGel polymeric sand data sheet (Techniseal, 2023)
- Technical Note 10, Dimensioning and Estimating Brick Masonry (Brick Industry Association, 2009)
- Calculating wallpaper quantities (Farrow & Ball)
- Primed MDF baseboard mouldings (lengths) (Metrie)
- Decking Installation Guide (Trex)
- NIST Handbook 44 (2026), Appendix C: General tables of units of measurement (National Institute of Standards and Technology, 2026)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: square footage of any rooms you draw, with paint, tile, drywall, flooring, carpet, roofing, pavers, brick, wallpaper, baseboard and deck board pages.
How the carpet is worked out
Carpet is cut from a roll of a fixed width, so a room takes whole widths, called drops, each as long as the room. A 15 × 12 ft room from a 12 ft roll is one drop 15 ft long: 180 sq ft, 20 square yards, with no seam. Turned the other way it would be two drops of 12 ft, with a seam and 288 sq ft of carpet. The calculator works out both directions and shows the one that uses less.
For an 18 × 14 ft room from a 12 ft roll: running along the 18 ft side takes 2 drops, 37.3 square yards, with 1 seam; the other way round is 48.0 square yards. Wider rolls, where a carpet comes in them, can save the seam.
The Carpet and Rug Institute’s installation standard asks for as few seams as possible, running the length of the room and the way people walk, out of strong light, and with the pile running the same way in every piece. That can mean choosing the direction with more carpet; the other direction is always shown so you can.
carpet = drops × room length × roll width; drops = ⌈ room width ÷ roll width ⌉
- Keep seams to a minimum, running the length of the area, parallel to the main traffic, not across doorways. Source: CRI 105, Standard for Installation of Residential Carpet.
- Adjacent pieces of the same carpet must have the pile running the same way. Source: CRI 105, Standard for Installation of Residential Carpet.
Carpet for common rooms
From a 12 ft roll, the direction that uses less; the last column from a 15 ft roll.
| Room | Floor | To buy (12 ft roll) | Drops | To buy (15 ft roll) |
|---|---|---|---|---|
| 10 × 10 ft | 11.1 sq yd | 13.3 sq yd | 1 | 16.7 sq yd |
| 12 × 10 ft | 13.3 sq yd | 13.3 sq yd | 1 | 16.7 sq yd |
| 12 × 12 ft | 16.0 sq yd | 16.0 sq yd | 1 | 20.0 sq yd |
| 14 × 12 ft | 18.7 sq yd | 18.7 sq yd | 1 | 20.0 sq yd |
| 15 × 12 ft | 20.0 sq yd | 20.0 sq yd | 1 | 20.0 sq yd |
| 16 × 14 ft | 24.9 sq yd | 37.3 sq yd | 2 | 26.7 sq yd |
| 18 × 14 ft | 28.0 sq yd | 37.3 sq yd | 2 | 30.0 sq yd |
| 20 × 16 ft | 35.6 sq yd | 42.7 sq yd | 2 | 53.3 sq yd |
Sources
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
How many square yards of carpet do I need?
Not just the floor area divided by 9: carpet comes off a roll, so you buy whole drops. For a 14 × 12 ft room from a 12 ft roll it is one drop of 14 ft, 18.7 square yards; a 16 × 14 ft room takes two drops of 14 ft, 37.3 square yards, though the floor is 24.9.
Why is the carpet more than the floor area?
Because the last drop is cut along its length to fit, and the strip left over is usually too narrow to use. A roll width that matches the room wastes least. Some installers also allow a few inches at each end for trimming.
Which way should the carpet run?
The CRI standard prefers seams running the length of the room and parallel to the main traffic, away from doorways and bright windows. The calculator shows both directions, so you can pick the one that puts the seam somewhere sensible.