Skip to content

Resistor Color Code Calculator

Tap the bands to read a resistor, or type a value to see its colours.

Tap the bands on the resistor to read its value, or type a value to see its colours: 4, 5 and 6 bands, with the tolerance range and the nearest standard value.

1234

Tap a band, on the resistor or above, to change its colour.

4-band resistor

4.7kΩ

Yellow, violet, red, gold: 47 × 100 = 4,700 Ω, ±5%, so anywhere from 4.465 kΩ to 4.935 kΩ.

Range at ±5%
4.465 kΩ to 4.935 kΩ
Standard value
Yes, in E12 and E24

Type 4.7k, 4k7, 220, 1M or 0.47; the bands follow.

Try
How this works: 8 sources,

How this works

Method

The colour code follows IEC 60062: digit bands, a multiplier and a tolerance (and a temperature coefficient on six bands), read in both directions. Standard values come from the IEC 60063 E-series, compared by ratio. Resistors add in series and their reciprocals add in parallel (capacitors the other way round); a divider gives Vin × R2 ÷ (R1 + R2), and an LED resistor is (Vs − n × Vf) ÷ I rounded up to the next standard value.

How it’s tested

24 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: the colour code on a resistor you can tap, with series and parallel, capacitors, voltage divider, LED resistor, SMD code and standard value pages.

Every change on What’s new

How we make toolsReport a mistake

Key facts

  • IEC 60062 assigns black to white the digits 0 to 9, gold and silver the multipliers ×0.1 and ×0.01, and pink ×0.001.
  • Gold means ±5%, silver ±10%, brown ±1%, red ±2%, and no tolerance band ±20%.
  • Yellow, violet, red, gold reads 47 × 100 = 4,700 Ω ±5%: anywhere from 4,465 to 4,935 Ω.

Sources: IEC 60062:2016+AMD1:2019; Wikipedia, Electronic color code

All 7 calculators

Combining parts · Circuits · Codes and values

The resistor colour code

IEC 60062, including the 2016 edition’s tolerance colours (orange ±0.05%, yellow ±0.02%, grey ±0.01%).

Resistor colour code
ColourDigitMultiplierToleranceTemp. coefficient
Black0×1–250 ppm/K
Brown1×10±1%100 ppm/K
Red2×100±2%50 ppm/K
Orange3×1,000±0.05%15 ppm/K
Yellow4×10,000±0.02%25 ppm/K
Green5×100,000±0.5%20 ppm/K
Blue6×1,000,000±0.25%10 ppm/K
Violet7×10⁷±0.1%5 ppm/K
Grey8×10⁸±0.01%1 ppm/K
White9×10⁹––
Gold–×0.1±5%–
Silver–×0.01±10%–
Pink–×0.001––

Every band means something by its position. The digit bands spell out the significant figures, the multiplier band says how many zeros to add (or, for gold, silver and pink, where to put the decimal point), and the band after it is the tolerance. That is why the same red can mean 2, ×100 or ±2% on one resistor.

Some makers still use grey for ±0.05% (the older EIA rule) and yellow or grey in place of gold and silver on high-voltage parts, so check the datasheet when a reading looks odd. Wire-wound resistors may have a wide first band.

Sources

IEC 60062 names the colours but sets no exact shades; the ones drawn here are for reading, and real bands vary with paint and light.

Common questions

How do I read a resistor colour code?

Hold the resistor with the tolerance band (often gold or silver, a little apart from the rest) on the right. On a 4-band resistor the first two bands are digits, the third is the multiplier and the fourth the tolerance: yellow (4), violet (7), red (×100), gold (±5%) is 4,700 Ω ±5%. Five and six bands add a third digit, and the sixth band is the temperature coefficient.

Which end do I start reading from?

The end whose band is closest to the lead. The tolerance band is usually set apart, and gold, silver and pink never come first because they have no digit. If both readings look possible, the one that gives a standard E-series value is almost always right.

What do 5 and 6 band resistors mean?

Precision resistors (1% and better) need three significant digits, so they have three digit bands, a multiplier and a tolerance. A sixth band gives the temperature coefficient: brown is 100 ppm/K, red 50, yellow 25 and so on.

Is a mnemonic the best way to remember the colours?

The order is the rainbow in the middle: black 0, brown 1, then red, orange, yellow, green, blue, violet for 2 to 7, then grey 8 and white 9. Many people find that easier than the old rhymes, and this page’s band picker shows each colour’s number as you go.

Why does my resistor measure a little off?

The tolerance band says how far it may be from its marked value: ±5% for gold, so a 4.7 kΩ resistor can read anywhere from 4,465 to 4,935 Ω. In a circuit, other parts in parallel also change the reading; measure it out of the circuit.