SMD Resistor Code Calculator
Type the code printed on a chip resistor (103, 4702, 4R7, 01C) to get its value…
Type the code printed on a chip resistor (103, 4702, 4R7, 01C) to get its value, or type a value to see how it is marked.
Type 103, 4702, 4R7 or 01C to read a code; 4.7kΩ to get its codes.
Code 472
4.7kΩ
472 is 4.7 kΩ: 3-digit code (2 digits and a multiplier, usually 5% parts).
- 3-digit code
- 472
- 4-digit code
- 4701
- EIA-96 code
- not an E96 value
How this works: 8 sources,
How this works
Method
Chip resistors are too small for colour bands, so they carry a short printed code. The 3-digit code is the colour code in numbers: two significant digits, then how many zeros follow. 472 is 47 followed by two zeros, 4,700 Ω; 103 is 10 kΩ; 100 is 10 Ω, not 100 Ω. Full method
Sources
- IEC 60062:2016+AMD1:2019, Marking codes for resistors and capacitors (IEC, 2016)
- IEC 60063:2015, Preferred number series for resistors and capacitors (IEC, 2015)
- Electronic color code (the IEC 60062:2016 table) (Wikipedia)
- University Physics Volume 2, §10.2 Resistors in Series and Parallel (OpenStax (Ling, Sanny and Moebs), 2016)
- University Physics Volume 2, §8.2 Capacitors in Series and in Parallel (OpenStax (Ling, Sanny and Moebs), 2016)
- E series of preferred numbers (Wikipedia)
- Light-emitting diode: colours, wavelengths and voltage drops (Wikipedia)
- SD-18 Part Requirements and Application Guide: Resistors, derating (NAVSEA, NSWC Crane)
How it’s tested
4 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: the colour code on a resistor you can tap, with series and parallel, capacitors, voltage divider, LED resistor, SMD code and standard value pages.
How to read SMD resistor codes
Chip resistors are too small for colour bands, so they carry a short printed code. The 3-digit code is the colour code in numbers: two significant digits, then how many zeros follow. 472 is 47 followed by two zeros, 4,700 Ω; 103 is 10 kΩ; 100 is 10 Ω, not 100 Ω.
Precision parts (1% and better) use 4 digits, three significant and a multiplier: 4702 is 47.0 kΩ and 1002 is 10.0 kΩ. Below 10 Ω (100 Ω with four digits) an R stands where the decimal point goes, so 4R7 is 4.7 Ω and R100 is 0.1 Ω. A plain 0 or 000 is a zero-ohm link, used as a jumper.
The smallest chips (0603 and smaller) use EIA-96: two digits that number a value in the E96 series (01 is 100, 68 is 499) and a letter for the multiplier (A ×1, B ×10, C ×100, D ×1000, X ×0.1, Y ×0.01). 01C is 100 × 100 = 10 kΩ; 68X is 49.9 Ω.
3 digits: ab c = ab × 10^c · 4 digits: abc d = abc × 10^d · EIA-96: value(nn) × letter
- IEC 60062 sets the letter and digit codes for resistor values, including R as the decimal marker (4R7 = 4.7 Ω). Source: IEC 60062:2016+AMD1:2019, Marking codes for resistors and capacitors.
- The E96 series behind EIA-96 codes has 96 values per decade, each about 2.4% above the last, for 1% tolerance parts. Source: IEC 60063:2015, Preferred number series for resistors and capacitors.
Common values and their SMD codes
The 3-digit, 4-digit and EIA-96 codes for common values, worked out by the calculator’s own code. A dash: that code can’t show the value.
| Value | 3-digit | 4-digit | EIA-96 |
|---|---|---|---|
| 100 mΩ | R10 | R100 | 01Z |
| 1 Ω | 1R0 | 1R00 | 01Y |
| 4.7 Ω | 4R7 | 4R70 | – |
| 10 Ω | 100 | 10R0 | 01X |
| 47 Ω | 470 | 47R0 | – |
| 100 Ω | 101 | 1000 | 01A |
| 220 Ω | 221 | 2200 | – |
| 470 Ω | 471 | 4700 | – |
| 1 kΩ | 102 | 1001 | 01B |
| 2.2 kΩ | 222 | 2201 | – |
Show all 16 rowsShow fewer
| 4.7 kΩ | 472 | 4701 | – |
| 10 kΩ | 103 | 1002 | 01C |
| 22 kΩ | 223 | 2202 | – |
| 47 kΩ | 473 | 4702 | – |
| 100 kΩ | 104 | 1003 | 01D |
| 1 MΩ | 105 | 1004 | 01E |
Common questions
Is 100 on a chip resistor 100 Ω?
No, it is 10 Ω: 10 followed by no zeros. 101 is 100 Ω and 102 is 1 kΩ. The last digit always counts zeros.
What does 01C mean?
It is an EIA-96 code: 01 is the first E96 value, 100, and C multiplies by 100, so 10 kΩ. These codes appear on 1% parts too small for four digits.
What is a resistor marked 000?
A zero-ohm resistor: a link in a resistor’s package, so a pick-and-place machine can fit jumpers and optional connections like any other part.