Voltage Divider Calculator
Two resistors turn a voltage into a smaller one.
Two resistors turn a voltage into a smaller one. Get Vout from R1 and R2, see what a load does to it, or find a standard pair for the voltage you need.
Load on the outputNo load (an open output or a high-impedance input)
What the output feeds. Leave it empty for an ADC or op-amp input.
ExampleOutput voltage
3.837V
10 kΩ over 4.7 kΩ divides 12 V down to 3.837 V.
Enter your own voltages and resistors to see your result.
- Divider current
- 816.3 µA
- Power in R1 and R2
- 6.664 mW and 3.132 mW
- Ratio Vout ÷ Vin
- 0.3197
How this works: 9 sources,
How this works
Method
Two resistors in series share the input voltage in proportion to their resistances, and the voltage across the bottom one is the output: Vout = Vin × R2 ÷ (R1 + R2). With 12 V, R1 = 10 kΩ and R2 = 4.7 kΩ, Vout = 12 × 4.7 ÷ 14.7 = 3.84 V. Full method
Sources
- University Physics Volume 2, §10.2 Resistors in Series and Parallel (OpenStax (Ling, Sanny and Moebs), 2016)
- Voltage divider (loading effect) (Wikipedia)
- IEC 60062:2016+AMD1:2019, Marking codes for resistors and capacitors (IEC, 2016)
- IEC 60063:2015, Preferred number series for resistors and capacitors (IEC, 2015)
- Electronic color code (the IEC 60062:2016 table) (Wikipedia)
- University Physics Volume 2, §8.2 Capacitors in Series and in Parallel (OpenStax (Ling, Sanny and Moebs), 2016)
- E series of preferred numbers (Wikipedia)
- Light-emitting diode: colours, wavelengths and voltage drops (Wikipedia)
- SD-18 Part Requirements and Application Guide: Resistors, derating (NAVSEA, NSWC Crane)
How it’s tested
3 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: the colour code on a resistor you can tap, with series and parallel, capacitors, voltage divider, LED resistor, SMD code and standard value pages.
How a voltage divider works
Two resistors in series share the input voltage in proportion to their resistances, and the voltage across the bottom one is the output: Vout = Vin × R2 ÷ (R1 + R2). With 12 V, R1 = 10 kΩ and R2 = 4.7 kΩ, Vout = 12 × 4.7 ÷ 14.7 = 3.84 V.
Anything connected to the output draws current and sits in parallel with R2, pulling the output down. A 10 kΩ load on that divider makes the bottom half 3.2 kΩ and the output 2.91 V, 24% low. Keep the load at least ten times R2, or use bigger currents (smaller resistors) or a buffer; that is why dividers suit reference inputs, sensors and ADC pins, not power.
To design one, the ratio R2 ÷ (R1 + R2) has to equal Vout ÷ Vin, and the pair has to come from the values you can buy. For 3.3 V from 5 V the ratio is 0.66; the calculator searches the E-series for the closest pair, such as 4.7 kΩ over 9.1 kΩ, which gives 3.30 V.
Vout = Vin × R2 ÷ (R1 + R2) · with a load: R2 → R2 × RL ÷ (R2 + RL)
- A divider is two resistors in series, so the same current flows through both and each drops I × R (series resistors, OpenStax §10.2). Source: University Physics Volume 2, §10.2 Resistors in Series and Parallel.
- Loading a divider with a resistance in parallel with R2 lowers the output; the unloaded formula only holds when the load draws negligible current. Source: Voltage divider (loading effect).
Standard E24 pairs for common conversions
R1 on top, R2 at the bottom, near 10 kΩ in total, and the output they give with no load.
| Vin to Vout | R1 | R2 | Actual Vout |
|---|---|---|---|
| 5 V to 3.3 V | 4.7 kΩ | 9.1 kΩ | 3.297 V |
| 5 V to 2.5 V | 5.1 kΩ | 5.1 kΩ | 2.5 V |
| 5 V to 1.8 V | 11 kΩ | 6.2 kΩ | 1.802 V |
| 12 V to 5 V | 5.1 kΩ | 3.6 kΩ | 4.966 V |
| 12 V to 3.3 V | 2.4 kΩ | 910 Ω | 3.299 V |
| 9 V to 5 V | 2.4 kΩ | 3 kΩ | 5 V |
| 24 V to 5 V | 9.1 kΩ | 2.4 kΩ | 5.009 V |
| 24 V to 12 V | 5.1 kΩ | 5.1 kΩ | 12 V |
| 3.3 V to 1.65 V | 5.1 kΩ | 5.1 kΩ | 1.65 V |
| 3.3 V to 1.2 V | 8.2 kΩ | 4.7 kΩ | 1.202 V |
Show all 12 rowsShow fewer
| 15 V to 10 V | 1.8 kΩ | 3.6 kΩ | 10 V |
| 48 V to 3.3 V | 27 kΩ | 2 kΩ | 3.31 V |
Common questions
Can I power something from a voltage divider?
Not usefully. The output falls as soon as the load draws current, and the divider wastes power all the time. Use a regulator for power; a divider is for signals, references and measuring voltages.
How do I pick the resistor values?
Choose the ratio from the voltages, then the size from the current: smaller resistors make a stiffer output but draw more current, larger ones save power but are more affected by the load and by noise. Around 10 kΩ total is a common start for logic and ADC inputs.
Does a divider work on AC?
Yes, with resistors it divides AC the same way at low frequencies. At high frequencies stray capacitance matters, which is why oscilloscope probes add a trimmer capacitor.
How do I measure 12 V with a 3.3 V microcontroller?
Use a divider that brings the highest voltage you expect under 3.3 V: for up to 15 V, 10 kΩ over 2.7 kΩ gives 3.19 V. Check the ADC input’s own resistance and add a margin.