Gravel Calculator
Tons and cubic yards of gravel for a driveway, path or pad…
Tons and cubic yards of gravel for a driveway, path or pad, allowing for loose stone settling tighter when it is compacted.
More options0% extra · 2,500 lb/yd³ loose · compacted +27%
Extra to allow
For spillage and uneven ground. A compacted layer’s own shrinkage is counted separately, from the loose and compacted weights.
MoDOT’s tables put loose gravel at 2,410 to 2,590 lb/yd³. Your supplier’s figure is better: put it here.
TxDOT: tandem dump trucks usually carry 12 or 14 cubic yards; single-axle trucks about 6.
ExampleGravel to order
14.14tons
11.31 cu yd loose, to compact to 8.89 cu yd.
Enter yours to see your result.
Bag size
- In bags
- 566 × 50 lb
- Extra for compaction
- 27%
- Area
- 720 sq ft
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
My shopping list
Add each part of a job and print one list: a paver patio is base stone, bedding sand and the pavers; a fence is post holes. It stays on this device.
How this works: 9 sources,
How this works
Method
Gravel is sold loose, by the cubic yard or the ton, but a driveway is measured after it has been spread and compacted. Compacting packs the stone tighter, so a 4 inch compacted layer needs more than 4 inches of loose stone. The calculator uses the Missouri Department of Transportation’s tables, which give both weights for the same crushed rock: about 2,500 lb per cubic yard loose and 3,180 compacted for limestone or granite, so a compacted layer takes 27% more loose stone. Full method
Sources
- Highway Maintenance Tables and Conversion Factors: loose and compacted weights of materials (Missouri Department of Transportation, Engineering Policy Guide)
- Seal Coat and Surface Treatment Manual: haul trucks, size (Texas Department of Transportation)
- QUIKRETE Concrete Mix (No. 1101) data sheet (QUIKRETE, revised October 2022)
- Sakrete High Strength Concrete Mix data sheet (Sakrete (Oldcastle APG), REV 7-10)
- Sakrete Concrete Mix product data sheet (30 kg) (Sika Canada)
- CIP 31, Ordering Ready Mixed Concrete (National Ready Mixed Concrete Association, 2023)
- CIP 8, Discrepancies in Yield (National Ready Mixed Concrete Association)
- International Residential Code 2021: R311.3, R311.7.5, R403.1.1, R506.1 (International Code Council, 2021)
- NIST Handbook 44 (2026), Appendix C: General tables of units of measurement (National Institute of Standards and Technology, 2026)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: draw any area and see bags on a pallet, yards or trucks, with 14 job and material pages and a shopping list kept on your device.
How gravel is worked out
Gravel is sold loose, by the cubic yard or the ton, but a driveway is measured after it has been spread and compacted. Compacting packs the stone tighter, so a 4 inch compacted layer needs more than 4 inches of loose stone. The calculator uses the Missouri Department of Transportation’s tables, which give both weights for the same crushed rock: about 2,500 lb per cubic yard loose and 3,180 compacted for limestone or granite, so a compacted layer takes 27% more loose stone.
As a second example, a 10 × 100 ft lane with 6 inches of compacted gravel is 1,000 × 0.5 = 500 cubic feet as laid, 18.5 cubic yards. It needs 23.6 cubic yards loose, which weighs 29.4 tons: two tandem truckloads.
Gravel varies with the rock and its size, so the default weight (2,500 lb per cubic yard loose, about 1,483 kg/m³) is a starting point. Your quarry or yard will know the figure for the stone they sell; put it under More options and the tons follow.
tons = area × depth ÷ 324 × compacted weight (lb/yd³) ÷ 2,000
- Loose granite or limestone weighs about 2,410 to 2,590 lb per cubic yard; compacted, 3,060 to 3,300. Source: Highway Maintenance Tables and Conversion Factors: loose and compacted weights of materials.
- Tandem-axle dump trucks usually carry 12 or 14 cubic yards of aggregate; single-axle trucks about 6. Source: Seal Coat and Surface Treatment Manual: haul trucks, size.
Gravel per 100 square feet
Loose at 2,500 lb/yd³; compacted at 3,180 lb/yd³ (MoDOT). The compacted columns are the loose stone to order for that finished depth.
| Depth | Loose: yards | Loose: tons | Compacted: yards to order | Compacted: tons |
|---|---|---|---|---|
| 2 in | 0.62 yd³ | 0.77 tons | 0.79 yd³ | 0.98 tons |
| 3 in | 0.93 yd³ | 1.16 tons | 1.18 yd³ | 1.47 tons |
| 4 in | 1.23 yd³ | 1.54 tons | 1.57 yd³ | 1.96 tons |
| 6 in | 1.85 yd³ | 2.31 tons | 2.36 yd³ | 2.94 tons |
| 8 in | 2.47 yd³ | 3.09 tons | 3.14 yd³ | 3.93 tons |
| 12 in | 3.70 yd³ | 4.63 tons | 4.71 yd³ | 5.89 tons |
Common questions
How much gravel do I need for a driveway?
For a 12 × 60 ft driveway with 4 inches of compacted gravel: 720 sq ft × 4 ÷ 324 = 8.9 cubic yards as laid, 11.3 cubic yards loose to order, about 14.1 tons. Many driveways are built in layers, a coarse base under a finer top, so work out each layer at its own depth and add them to your list.
How many tons of gravel in a cubic yard?
About 1.2 to 1.3 tons loose for crushed limestone or granite, from MoDOT’s tables (2,410 to 2,590 lb), and 1.5 to 1.65 tons once compacted. Rounded river gravel and wet stone differ, so ask your supplier for theirs.
Should I measure loose or compacted?
Measure the depth you want when it is finished. If the gravel will be compacted with a plate or roller, as a driveway or base should be, pick Compacted and the calculator orders the extra loose stone. For a decorative layer that is raked, not compacted, pick Loose.