Stud Calculator
Studs for a wall at your spacing, with the extras corners and openings take…
Studs for a wall at your spacing, with the extras corners and openings take, and the plates along the top and bottom.
Spacing, on center
Corners
Doors and windows
ExampleStuds to buy
19studs
11 at 16 in on center, plus 8 for corners and openings; 42 ft of plate.
Enter yours to see your result.
- Plates (double top, one bottom)
- 42 ft
- Stud length
- 8 ft
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
My shopping list
Add each part of a job and print one list. It stays on this device.
How this works: 1 source,
How this works
Method
Studs stand at a set spacing, measured center to center: 16 inches is usual for walls, 24 inches where the design allows it. A wall needs one stud at each spacing along its length plus one at the end, so a 12 ft wall at 16 in on center takes 144 ÷ 16 + 1 = 10 studs. Corners take extra studs to give both walls a nailing surface, and every door or window takes a king stud and a jack stud on each side. Full method
Sources
- Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (board measure, Table 3 sizes, standard lengths) (National Institute of Standards and Technology, 2025)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: board feet for a lumber list, plywood and board cut lists with kerf, studs for a wall and nominal against actual lumber sizes.
How the studs are worked out
Studs stand at a set spacing, measured center to center: 16 inches is usual for walls, 24 inches where the design allows it. A wall needs one stud at each spacing along its length plus one at the end, so a 12 ft wall at 16 in on center takes 144 ÷ 16 + 1 = 10 studs. Corners take extra studs to give both walls a nailing surface, and every door or window takes a king stud and a jack stud on each side.
For a 20 ft garage wall at 24 in on center with one corner and two openings: 240 ÷ 24 + 1 = 11 studs, plus 2 for the corner and 8 for the openings, 21 in all. Plates run the wall’s length three times, a doubled top plate and a bottom plate: 60 ft.
This is a take-off for buying, not a framing plan: headers, cripples, blocking and the exact corner detail depend on your design and your building code. Many people add a few studs for warped ones and mistakes.
studs = ⌊ length ÷ spacing ⌋ + 1 + 2 × corners + 4 × openings
- A 2×4 stud measures 1½ × 3½ in dry; studs are dimension lumber. Source: Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (board measure, Table 3 sizes, standard lengths).
Studs by wall length
Studs at 16 and 24 in on center, before corners and openings; plates are 3 × the length.
| Wall | At 16 in | At 24 in | Plate |
|---|---|---|---|
| 8 ft | 7 | 5 | 24 ft |
| 10 ft | 8 | 6 | 30 ft |
| 12 ft | 10 | 7 | 36 ft |
| 14 ft | 11 | 8 | 42 ft |
| 16 ft | 13 | 9 | 48 ft |
| 20 ft | 16 | 11 | 60 ft |
| 24 ft | 19 | 13 | 72 ft |
Sources
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
How many studs for a 12 ft wall?
At 16 in on center, 10 studs (144 ÷ 16 + 1), before the extras for corners and openings. At 24 in on center, 7.
What does 16 inches on center mean?
The distance from the middle of one stud to the middle of the next is 16 inches. Three spacings make 48 inches, so the edges of a 4 ft wide sheet land on a stud.
How many studs does a window need?
At least a king stud and a jack stud on each side, four in all, plus short cripple studs above and below that depend on the size. The calculator adds four per opening; add cripples for big windows.