Cut List Calculator
The pieces you need, packed into the board length you buy…
The pieces you need, packed into the board length you buy, so you know how many boards and where each cut goes.
Compare lengths (boards needed)
ExampleBoards to buy
6× 8′
18 pieces; 105¾ in of offcuts and 2¼ in lost to the saw.
Enter yours to see your result.
- Kerf allowed
- 0.125 in
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
My shopping list
Add each part of a job and print one list. It stays on this device.
How this works: 1 source,
How this works
Method
A cut list turns the pieces you need into boards to buy. The calculator sorts the pieces longest first and cuts each one from the first board with room for it and a saw kerf, starting a new board only when none has room. That is first-fit decreasing, the standard way to pack lengths, and it uses offcuts before new boards, so the count is usually what a careful carpenter would buy. Full method
Sources
- Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (board measure, Table 3 sizes, standard lengths) (National Institute of Standards and Technology, 2025)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: board feet for a lumber list, plywood and board cut lists with kerf, studs for a wall and nominal against actual lumber sizes.
How the boards are worked out
A cut list turns the pieces you need into boards to buy. The calculator sorts the pieces longest first and cuts each one from the first board with room for it and a saw kerf, starting a new board only when none has room. That is first-fit decreasing, the standard way to pack lengths, and it uses offcuts before new boards, so the count is usually what a careful carpenter would buy.
For a bench: four 42 in legs and rails and two 20 in stretchers from 8 ft boards with a ⅛ in kerf. Two 42 in pieces take 84¼ in of a 96 in board, leaving room for nothing else, so the four 42s take two boards and the 20s a third: 3 boards, with 80.0 in left over.
Buy one length longer when a piece is close to a board’s length: boards are not always cut square at the ends, and a split end has to come off. The lumber standard sets lengths in steps of 1 or 2 ft, so 8, 10, 12, 14 and 16 ft boards are easy to find; try the lengths under the field and keep the one with the least left over.
boards = pieces packed longest first into stock lengths, a kerf per cut
- Standard lengths of lumber are in multiples of 1 foot or 2 feet, as the grading rules specify. Source: Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (board measure, Table 3 sizes, standard lengths).
Boards for common piece lists
With a ⅛ in kerf, from 8, 10 and 12 ft boards.
| Pieces | 8 ft boards | 10 ft boards | 12 ft boards |
|---|---|---|---|
| Eight 4 ft pieces | 8 | 4 | 4 |
| Six 30 in pieces | 2 | 2 | 2 |
| Four 5 ft pieces | 4 | 4 | 2 |
| Ten 18 in pieces | 2 | 2 | 2 |
| Three 7 ft pieces | 3 | 3 | 3 |
Sources
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their data sheets and guides are cited for the figures printed in them.
Common questions
What is a cut list?
The list of pieces a project needs, with their lengths and how many, and which board each is cut from. Working it out before you buy saves both a second trip and boards left over.
Should I allow for the saw blade?
Yes: each cut removes the blade’s kerf, about ⅛ in. Two 48 in pieces don’t come out of a 96 in board once the cut is taken; the calculator allows for it.
Which board length is best?
The one where your pieces leave the least offcut, which isn’t always the longest. Try 8, 10 and 12 ft with the chips and compare the counts and the leftover.