Skip to content

Plywood Cut Calculator

List the parts, and see how many sheets they take and where to cut each one…

List the parts, and see how many sheets they take and where to cut each one, with the blade’s kerf allowed between every part.

in
in
in
in
in
in
in
in
in

ExampleSheets to buy

1sheet

76% of the plywood ends up in parts.

Enter yours to see your result.

30×24 ↻30×24 ↻30×11.25 ↻30×11.25 ↻30×11.25 ↻30×11.25 ↻24×1524×15
Sheet 1 of 96 × 48 in · 76% used · ↻ turned
Parts
8
Kerf allowed
0.125 in

An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms

My shopping list

Add each part of a job and print one list. It stays on this device.

How this works: 1 source,

How this works

Method

Plywood and MDF come in sheets, most often 4 × 8 ft in North American stores, and parts are cut from them in straight, edge-to-edge (guillotine) cuts. The calculator sorts your parts largest first and lays them in rows across each sheet, turning a part when it fits better on its side, and leaves the saw’s kerf between every two parts. It tries several part orders and row arrangements and keeps the layout that uses the fewest sheets, then draws each sheet so you can mark it out; a ↻ marks a part it turned. Full method

How it’s tested

2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Limits

An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: board feet for a lumber list, plywood and board cut lists with kerf, studs for a wall and nominal against actual lumber sizes.

Every change on What’s new

How we make toolsReport a mistake

How the sheets are worked out

Plywood and MDF come in sheets, most often 4 × 8 ft in North American stores, and parts are cut from them in straight, edge-to-edge (guillotine) cuts. The calculator sorts your parts largest first and lays them in rows across each sheet, turning a part when it fits better on its side, and leaves the saw’s kerf between every two parts. It tries several part orders and row arrangements and keeps the layout that uses the fewest sheets, then draws each sheet so you can mark it out; a ↻ marks a part it turned.

A second example: two cabinet sides of 34½ × 22½ in and six drawer parts of 22½ × 16 in, with a ⅛ in kerf, fit on 2 sheets, 73% of the first one used. Tick “keep the grain” for veneered or figured faces and parts stay the way you entered them, which can take an extra sheet.

Kerf matters more than it looks. Four parts exactly 24 in wide don’t fit across a 96 in sheet once three ⅛ in saw cuts are taken out, so a layout that works on paper can need another sheet. The calculator starts at ⅛ in; thin-kerf blades cut narrower, so check the kerf printed on your blade’s packaging.

sheets = parts packed in rows (largest first), with a kerf between every two parts

Sheets of 4 × 8 ft for common part lists

With no kerf and with a ⅛ in kerf; parts may be turned.

With no kerf and with a ⅛ in kerf; parts may be turned.
PartsSheets, no kerfSheets, ⅛ in kerf
Cabinet sides 30 × 24 in, ×211
Shelves 30 × 11¼ in, ×811
Drawer bottoms 20 × 18 in, ×611
Panels 48 × 24 in, ×412
Panels 24 × 24 in, ×813
Strips 96 × 6 in, ×1022

Common questions

How many sheets of plywood do I need?

Add up the parts’ area for a lower bound (a 4 × 8 sheet is 32 sq ft), then lay them out, because parts rarely fill a sheet edge to edge. The calculator lays them out with the kerf and gives the count and the drawing.

What is kerf?

The width of wood the saw blade turns to dust in each cut, often about ⅛ in, less for a thin-kerf blade: the packaging gives it. Every part needs a kerf on each side it shares with another part.

Can I turn parts to fit?

For paint-grade plywood and MDF, yes, and the calculator does when it saves space. For veneered panels where the grain should run one way, tick keep the grain and parts stay as entered.