Stair Stringer Calculator
The stringer drawn the way you mark it on the board: each notch…
The stringer drawn the way you mark it on the board: each notch, the length of 2×12 it needs, the throat left under the cuts and how much to drop the bottom.
floor to floor or deck to ground · 4 ft 8 in
Risers
8 is the fewest that keep each riser at 7¾ in or less; more risers make a gentler stair that takes more floor.
Stringer board
More options1 in treads · IRC 2021
Check against
ExampleStringer length
7 ft 7 11/16 in
Mark 7 notches at 7 in rise and 10½ in run: buy 8 ft 2×12s, 3 stringers for 3 ft.
Enter yours to see your result.
- Angle
- 33.7°
- Throat left
- 5 7/16 in
- First riser cut
- 6 in
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
Code check · informational
- Riser height (within the limit)7¾ in at most; keep every riser within ⅜ in of the others. R311.7.5.17 in
- Tread depth, nosing to nosing (within the limit)10 in at least. R311.7.5.210½ in
- Nosing (within the limit)¾ in to 1¼ in on treads under 11 in. R311.7.5.31 in
- Rise of one flight (within the limit)12 ft 7 in at most between floors or landings. R311.7.34 ft 8 in
- Width (within the limit)36 in clear at least, above the handrail. R311.7.136 in
- Handrail on at least one sideWith 8 risers (4 or more): 34 in to 38 in above the nosings. R311.7.8, R311.7.8.1
- Throat of a cut stringer (within the limit)AWC’s deck guide sized 2×12 cut stringers with 5.1 in of wood left; three cut stringers at least, 18 in apart at most. AWC DCA 65 7/16 in
The 2021 International Residential Code, R311.7 and R312.1, as printed in the SMA’s visual interpretation. Informational: your town may adopt another edition or amend it, and its inspector decides.
My shopping list
Add each part of a job and print one list. It stays on this device.
How this works: 4 sources,
How this works
Method
A cut stringer is a board, usually a 2×12, with a saw-tooth of notches that the treads sit on. You mark it with a framing square: the riser height on the tongue, the tread run on the blade, both on the board’s top edge, and you step the square along once per tread. The calculator draws the board that way, flat, with each notch, so you can check the marks before you cut. Full method
Sources
- DCA 6, Prescriptive Residential Wood Deck Construction Guide (stair requirements and commentary) (American Wood Council, 2018)
- 2021 International Residential Code, R311.7 Stairways and R312.1 Guards (text as printed in the SMA Visual Interpretation of the 2021 IRC Stairbuilding Codes, 2023) (International Code Council; Stairway Manufacturers’ Association, 2023)
- Approved Document K: Protection from falling, collision and impact, 2013 edition (Table 1.1, paras 1.11, 1.34, 1.41) (HM Government (England), 2013)
- Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (dressed sizes, standard lengths) (National Institute of Standards and Technology, 2025)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: a staircase drawn to scale from its total rise, with the stringer layout, rise and run, deck stairs, stairs with a landing and the IRC and Approved Document K limits checked.
How the stringer is laid out
A cut stringer is a board, usually a 2×12, with a saw-tooth of notches that the treads sit on. You mark it with a framing square: the riser height on the tongue, the tread run on the blade, both on the board’s top edge, and you step the square along once per tread. The calculator draws the board that way, flat, with each notch, so you can check the marks before you cut.
The length it gives is the board the stringer needs, measured along the board from the toe on the floor to the plumb cut at the top, not just the diagonal of the stair. A worked example: 30 in from a patio up to a door, 11 in runs, 1½ in treads. 30 ÷ 7.75 = 3.87, so 4 risers of 7½ in. The stringer is 3 ft 7 5/16 in long and leaves 5 1/16 in of wood under the notches, so a 2×12 8 ft long is plenty.
Two cuts catch people out. The bottom riser on the stringer is cut shorter by one tread thickness, or the first step comes out taller than the rest once the treads go on; the calculator shows this as the first riser cut. And the throat, the wood left between the inside corner of each notch and the lower edge, is what carries the load: the American Wood Council’s deck guide sized its cut 2×12 stringers with about 5.1 in left, and flags less in red here.
length = ((n − 1) × run² + (n × rise − tread) × rise) ÷ √(rise² + run²); throat = depth − rise × run ÷ √(rise² + run²)
- All deck stair stringers shall be at least 2×12; with only cut stringers, at least three are needed, at most 18 in apart on centre for wider stairs. Source: DCA 6, Prescriptive Residential Wood Deck Construction Guide (stair requirements and commentary).
- Risers are at most 7¾ in and treads at least 10 in, and within a flight the largest may exceed the smallest by no more than ⅜ in (R311.7.5.1, R311.7.5.2). Source: 2021 International Residential Code, R311.7 Stairways and R312.1 Guards (text as printed in the SMA Visual Interpretation of the 2021 IRC Stairbuilding Codes, 2023).
Check it with a tape
For a quick check, the stringer is about the square root of total rise squared plus total run squared. For 56 in of rise and 73½ in of run that is √(56² + 73.5²) = 92.4 in, close to the 91 11/16 in the layout gives once the cuts at the ends are counted, so an 8 ft board.
Stringer lengths by total rise
Fewest risers under 7¾ in, a 10½ in run, 1 in treads and 2×12 stringers (11¼ in deep).
| Total rise | Risers | Stringer | Board | Throat |
|---|---|---|---|---|
| 1 ft 9 in | 3 × 7 in | 2 ft 4 9/16 in | 8 ft | 5 7/16 in |
| 2 ft 4 in | 4 × 7 in | 3 ft 5 3/16 in | 8 ft | 5 7/16 in |
| 3 ft | 5 × 7 3/16 in | 4 ft 6 7/16 in | 8 ft | 5 5/16 in |
| 3 ft 6 in | 6 × 7 in | 5 ft 6 7/16 in | 8 ft | 5 7/16 in |
| 4 ft 8 in | 8 × 7 in | 7 ft 7 11/16 in | 8 ft | 5 7/16 in |
| 5 ft 10 in | 10 × 7 in | 9 ft 8⅞ in | 10 ft | 5 7/16 in |
| 7 ft | 11 × 7⅝ in | 11 ft 1¾ in | 12 ft | 5 1/16 in |
| 8 ft 9 in | 14 × 7½ in | 14 ft 3½ in | 16 ft | 5⅛ in |
Sources
- American Wood Council, DCA 6, Prescriptive Residential Wood Deck Construction Guide (stair requirements and commentary)
- International Code Council; Stairway Manufacturers’ Association, 2021 International Residential Code, R311.7 Stairways and R312.1 Guards (text as printed in the SMA Visual Interpretation of the 2021 IRC Stairbuilding Codes, 2023)
The codes are cited for their limits as published; the check on this page is informational, and the code your town adopts, with its amendments, is the one that applies.
Common questions
How do you lay out a stair stringer?
Clamp stair gauges, or mark, the riser height on the framing square’s tongue and the tread run on its blade. Lay the square on the board with both marks on the top edge, trace the notch, slide along to the end of the last mark and repeat once per tread. Then cut the bottom one tread thickness short.
What size board do I need for stair stringers?
A 2×12 for cut stringers in most cases: it leaves about 5 in under the notches at a 7¾ in rise and 10 in run. A 2×10 leaves only about 3 in at the same steps. Buy the next standard length longer than the stringer the calculator gives.
How many stringers do I need?
At least three cut stringers for a 36 in stair, per the American Wood Council’s deck guide, and no more than 18 in apart on centre for anything wider. The calculator counts them from the width.
Why is my bottom step taller than the others?
Because the stringer was not dropped. Every tread adds its thickness on top of the notch, but the bottom step has no tread below it, so cut that much off the bottom of the stringer and every riser comes out equal.