Skip to content

Stairs With Landing Calculator

A stair with a landing part way up, straight on, turning a corner or doubling back…

A stair with a landing part way up, straight on, turning a corner or doubling back, with the risers each side of it and the floor space it takes.

in

floor to floor · 13 ft

Shape

Risers up to the landing of 21

11
More options10 in run, 36 in wide · IRC 2021
in
in
in

Check against

ExampleSplit at the landing

11 + 10risers of 7 7/16 in

6 ft 9 11/16 in up to the landing and 6 ft 2 5/16 in above it; the stair takes 11 ft 4 in × 10 ft 6 in of floor.

Enter yours to see your result.

Landing11 up10 up11 ft 4 in10 ft 6 in3 ft × 3 ft
Plan from above: 11 risers to a square landing as wide as the stair, then 10 more after a quarter turn.
Treads
10 + 9 of 10 in
Angle
36.6°

An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms

Code check · informational

  • Riser height (within the limit)7¾ in at most; keep every riser within ⅜ in of the others. R311.7.5.17 7/16 in
  • Tread depth, nosing to nosing (within the limit)10 in at least. R311.7.5.210 in
  • Nosing (within the limit)¾ in to 1¼ in on treads under 11 in. R311.7.5.31 in
  • Rise of one flight (within the limit)12 ft 7 in at most between floors or landings; the taller flight is shown. R311.7.36 ft 9 11/16 in
  • Width (within the limit)36 in clear at least, above the handrail. R311.7.136 in
  • Handrail on at least one sideWith 21 risers (4 or more): 34 in to 38 in above the nosings. R311.7.8, R311.7.8.1

The 2021 International Residential Code, R311.7 and R312.1, as printed in the SMA’s visual interpretation. Informational: your town may adopt another edition or amend it, and its inspector decides.

My shopping list

Add each part of a job and print one list. It stays on this device.

How this works: 4 sources,

How this works

Method

A landing splits a stair into two flights. The risers are all the same height, total rise ÷ risers, and the landing is simply the top step of the lower flight, so a flight of n risers still has n − 1 treads. Move the landing up or down the stair with the stepper: the split changes where the turn falls, not the riser height. Full method

How it’s tested

3 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Limits

An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: a staircase drawn to scale from its total rise, with the stringer layout, rise and run, deck stairs, stairs with a landing and the IRC and Approved Document K limits checked.

Every change on What’s new

How we make toolsReport a mistake

How a stair with a landing is laid out

A landing splits a stair into two flights. The risers are all the same height, total rise ÷ risers, and the landing is simply the top step of the lower flight, so a flight of n risers still has n − 1 treads. Move the landing up or down the stair with the stepper: the split changes where the turn falls, not the riser height.

The shape decides the footprint. Straight, the landing sits in the line of travel, at least 36 in deep under the IRC. A quarter turn (L) uses a square landing as wide as the stair, and a half turn (U) puts the flights side by side with the landing across both. For 120 in in a U with 10½ in runs: 16 risers of 7½ in, 8 below the landing and 8 above, in a footprint of 9 ft 5½ in by 6 ft with a 40 in landing.

The IRC requires a landing once a flight would climb more than 12 ft 7 in, and at the top and bottom of every stair. Otherwise a landing is a choice for fit or for comfort: an L or U stair fits where a straight run won’t, and a rest half way up is welcome on a tall stair.

n = ⌈rise ÷ 7¾⌉; flights n₁ + n₂ = n; straight length = (n₁ − 1 + n₂ − 1) × run + landing

Stairs with a landing by total rise

Fewest risers under 7¾ in, split about in half, at a 10 in run, 36 in wide with a 36 in landing.

Fewest risers under 7¾ in, split about in half, at a 10 in run, 36 in wide with a 36 in landing.
Total riseRisersSplitStraight lengthL footprint
9 ft14 × 7 11/16 in7 + 713 ft8 ft × 8 ft
10 ft16 × 7½ in8 + 814 ft 8 in8 ft 10 in × 8 ft 10 in
11 ft18 × 7 5/16 in9 + 916 ft 4 in9 ft 8 in × 9 ft 8 in
12 ft19 × 7 9/16 in10 + 917 ft 2 in10 ft 6 in × 9 ft 8 in
12 ft 7 in20 × 7 9/16 in10 + 1018 ft10 ft 6 in × 10 ft 6 in
13 ft21 × 7 7/16 in11 + 1018 ft 10 in11 ft 4 in × 10 ft 6 in
14 ft22 × 7⅝ in11 + 1119 ft 8 in11 ft 4 in × 11 ft 4 in
15 ft24 × 7½ in12 + 1221 ft 4 in12 ft 2 in × 12 ft 2 in

Common questions

When does a stair need a landing?

Under the IRC, when one flight would rise more than 12 ft 7 in (151 in) between floors, and always at the top and bottom of a stair. Many stairs add one anyway to turn a corner.

How big does a stair landing need to be?

At least as wide as the stair and, on a straight run, at least 36 in deep in the direction of travel under the IRC. A turning landing is usually square, as wide as the stair each way.

Where should the landing go?

Anywhere that fits the plan; the risers stay the same height either way. Half way up is the usual choice, and a turn near the top or bottom can save the most floor.

How much space does an L-shaped stair take?

The lower flight’s treads plus the stair width one way, and the stair width plus the upper flight’s treads the other. Enter your rise and width and the plan gives the footprint.