Board on Board Fence Calculator
Boards for a board on board fence, alternating front and back with the overlap you…
Boards for a board on board fence, alternating front and back with the overlap you choose, plus the posts and rails for its length.
Gates
Height
Posts at most
More options3½ in posts · 5½ in boards, 1 in overlap · 3 rails · 3 ft in the ground · prices
Posts
Rails per section
QUIKRETE’s rule buries a third of the post and adds 6 in of gravel. Where the ground freezes, go below the frost line your building department gives.
Concrete bags
Your prices (optional, each)
ExampleBoard on board
214boards
80 ft of fence: 10 sections between 11 posts, 30 rails and 214 boards.
Enter yours to see your result.
| Posts | 11 × 10 ft | 4×4; 0 corner, 2 end, 0 gate, 9 line |
|---|---|---|
| Rails | 30 × 8 ft | 3 a section |
| Boards | 214 × 6 ft | 1×6; front and back, 1 in overlap |
| Concrete | 32 × 80 lb | 10½ in holes, +10% |
| Gravel | 3.3 cu ft | 6 in under each post |
Concrete per hole and bag sizes: post hole concrete calculator.
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department. Terms
My shopping list
Add each part of a job and print one list. It stays on this device.
How this works: 4 sources,
How this works
Method
A board on board fence has two layers: boards on one side of the rails with gaps between them, and boards on the other side covering those gaps, each lapping its neighbours. Counted along the fence, every board after the first adds its width less the overlap, so a stretch of length L takes (L − w) ÷ (w − overlap) + 1 boards, rounded up. The overlap keeps the fence private as the boards shrink. Full method
Sources
- Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (dressed sizes, standard lengths) (National Institute of Standards and Technology, 2025)
- Setting Posts project sheet (QUIKRETE)
- QUIKRETE Concrete Mix (No. 1101) data sheet (QUIKRETE, revised October 2022)
- CIP 31, Ordering Ready Mixed Concrete (National Ready Mixed Concrete Association, 2023)
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Limits
An estimate of materials to buy, not engineering or code advice. Check sizes with your supplier and local building department.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: a fence of any shape drawn from above and in elevation, with posts, rails, boards, pickets or panels, gates and concrete.
How the boards are counted
A board on board fence has two layers: boards on one side of the rails with gaps between them, and boards on the other side covering those gaps, each lapping its neighbours. Counted along the fence, every board after the first adds its width less the overlap, so a stretch of length L takes (L − w) ÷ (w − overlap) + 1 boards, rounded up. The overlap keeps the fence private as the boards shrink.
A worked example: an L of 50 and 30 ft with a 4 ft gate, 5½ in boards overlapping 1½ in, three rails, posts at most 8 ft apart: 228 boards, 13 posts and 33 rails. A butted privacy fence of the same boards would take about 168, so board on board takes 36% more boards for the same length.
The drawing shows the back layer lighter behind the rails and the front layer over it. The overlap is your choice: 1 in is common with 1×6 boards; more overlap hides more as the boards dry and shrink, at the cost of more boards.
boards per stretch = ⌈(length − width) ÷ (width − overlap)⌉ + 1
- A 1×6 board is ¾ × 5½ in dry and dressed; a 1×8 ¾ × 7¼ in. Source: Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (dressed sizes, standard lengths).
- Fence posts: a third of the post’s length in the ground, in a hole three times its width, on 6 in of gravel. Source: Setting Posts project sheet.
Boards per 100 ft, board on board and butted
One straight run, no gates.
| Boards | Board on board | Butted |
|---|---|---|
| 5½ in boards, 1 in overlap | 267 | 219 |
| 5½ in boards, 1½ in overlap | 300 | 219 |
| 5½ in boards, 2 in overlap | 343 | 219 |
| 3½ in boards, 1 in overlap | 480 | 343 |
| 7¼ in boards, 1½ in overlap | 209 | 166 |
Sources
- National Institute of Standards and Technology, Voluntary Product Standard PS 20-25, American Softwood Lumber Standard (dressed sizes, standard lengths)
- QUIKRETE, Setting Posts project sheet
Product names are trademarks of their owners; Binary Decimal is not affiliated with any of them. Their instructions and data sheets are cited for the figures printed in them.
Common questions
How many boards do I need for a board on board fence?
About (length − board width) ÷ (board width − overlap) + 1. For 5½ in boards overlapping 1 in, that is 2.7 boards a foot, about 267 per 100 ft.
How much should board on board overlap?
An inch or so with 1×6 boards keeps the fence private once the boards shrink. More overlap means more boards; less risks gaps.
Is board on board more expensive than a privacy fence?
It uses more boards, a fifth to over a third more depending on the overlap, and the same posts and rails. It looks finished from both sides, which is why it is often chosen for a shared boundary.
How many rails for a 6 ft board on board fence?
Three per section is common for 6 ft fences, so the boards are held at the bottom, middle and top. Enter your design under More options.