PPM Calculator: ppm, ppb, mg/L and Molarity
Type a concentration in ppm, ppb, mg/L…
Type a concentration in ppm, ppb, mg/L, percent or molarity to see it in every other unit, and where it sits beside drinking water limits.
Read as NaCl · 58.44 g/mol
Example250 mg/L of NaCl
250ppm
250 mg in every litre of water, which is 4.28 mmol/L of NaCl. In dilute water solutions 1 ppm ≈ 1 mg/L.
Type your own concentration.
- ppm
- 250
- ppb
- 250,000
- ppt (trillion)
- 2.50 × 10⁸
How this works: 5 sources,
How this works
Method
Parts per million is a mass ratio: 1 ppm is 1 mg of solute in 1 kg of solution, 1 ppb is 1 µg per kg. For water and dilute water solutions a litre weighs very close to a kilogram, so 1 ppm is, for practical purposes, 1 mg/L, and that is how water test reports use the two interchangeably. Full method
Sources
How it’s tested
2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.
Privacy
On your device. Nothing you enter or open leaves this browser. About privacy labels
Changes
- First published: molarity with a recipe, dilution with a drawing of the two vessels, mass percent, ppm against drinking water limits, and pH solved exactly for strong and weak acids and bases.
How ppm, mg/L and molarity relate
Parts per million is a mass ratio: 1 ppm is 1 mg of solute in 1 kg of solution, 1 ppb is 1 µg per kg. For water and dilute water solutions a litre weighs very close to a kilogram, so 1 ppm is, for practical purposes, 1 mg/L, and that is how water test reports use the two interchangeably.
To get molarity, divide mg/L by the molar mass to get mmol/L. Sodium chloride is 58.44 g/mol, so 250 mg/L of it is 4.28 mmol/L, or 0.00428 M. Going the other way, multiply molarity by the molar mass and by 1,000 for mg/L.
The 1 mg/L = 1 ppm shortcut breaks down for dense solutions such as sea water or brines, where a litre weighs more than a kilogram, and for anything that isn’t water. Then ppm (mass per mass) and mg/L (mass per volume) differ by the density, and the tool’s answer, which assumes 1 kg per litre, is only an estimate.
1 ppm = 1 mg/kg ≈ 1 mg/L (water); mmol/L = mg/L ÷ molar mass
- US drinking water may hold at most 0.010 mg/L of arsenic, 4.0 mg/L of fluoride and 10 mg/L of nitrate (measured as nitrogen); copper triggers action above 1.3 mg/L. Source: US EPA, National Primary Drinking Water Regulations.
- The secondary, non-enforceable standards suggest at most 250 mg/L of chloride and 500 mg/L of total dissolved solids, for taste and appearance. Source: US EPA, Secondary Drinking Water Standards: Guidance for Nuisance Chemicals.
US drinking water limits in every unit
Each EPA limit as mg/L, ppm, ppb and percent, assuming 1 L of water weighs 1 kg.
| Limit | mg/L | ppm | ppb | Percent |
|---|---|---|---|---|
| Arsenic (MCL) | 0.010 | 0.010 | 10 | 1.0 × 10⁻⁶% |
| Copper (action level) | 1.3 | 1.3 | 1,300 | 1.3 × 10⁻⁴% |
| Fluoride (MCL) | 4.0 | 4.0 | 4,000 | 4.0 × 10⁻⁴% |
| Nitrate as N (MCL) | 10 | 10 | 10,000 | 0.0010% |
| Chloride (secondary) | 250 | 250 | 250,000 | 0.025% |
| Total dissolved solids (secondary) | 500 | 500 | 500,000 | 0.050% |
| Barium (MCL) | 2.0 | 2.0 | 2,000 | 2.0 × 10⁻⁴% |
| Sulfate (secondary) | 250 | 250 | 250,000 | 0.025% |
Common questions
Is ppm the same as mg/L?
For water and dilute water solutions, yes to within a fraction of a percent, because a litre weighs about a kilogram. For other liquids, multiply mg/L by the liquid’s density in kg/L to get ppm.
How do I convert ppm to ppb?
Multiply by 1,000. 0.010 ppm of arsenic is 10 ppb, and 2 ppm of barium is 2,000 ppb.
How do I convert ppm to molarity?
Divide the ppm (as mg/L) by the molar mass for millimoles per litre, then by 1,000 for moles per litre. Type the formula in the box and it is done for you.
What does ppm mean for gases?
In air, ppm usually counts molecules (by volume), not mass: 420 ppm of carbon dioxide means 420 of every million air molecules. This page is for solutions in water, by mass.