Skip to content

Wheel Offset Calculator

Compare your wheel with a new one by width and offset: the backspacing of each…

Compare your wheel with a new one by width and offset: the backspacing of each, and how far the new rim sits further out toward the fender or further in toward the suspension.

Current wheel
in
mm
New wheel
in
mm

Width is the number after the x in 17x8. Offset is stamped as ET (ET45 is +45 mm); a negative offset pushes the wheel out.

More optionsBackspacing counts 1 in of flanges
in

How much wider the wheel is over its flanges than its nominal width. About 1 inch on most wheels; measure yours for a close fit.

Outer edge moves

+22.7mm

Out toward the fender (+0.89 in). The inner edge moves +2.7 mm toward the suspension.

← inside (suspension)outside (fender) →mounting faceoldnew

Inner edge

+2.7 mm

closer to the suspension

Outer edge

+22.7 mm

further out (poke)

Backspacing
6.27 in → 6.38 in
Overall width
9 in → 10 in

Rim positions only; a wider tire bulges past the rim on both sides. Check brake, suspension and fender clearance before buying. Terms

How this works: 5 sources,

How this works

Method

Offset (ET, from the German Einpresstiefe) is the distance from the middle of the wheel to the face that bolts to the hub. Positive offset puts that face toward the outside, tucking the wheel in; negative offset pushes the wheel out. Most front-wheel-drive cars use high positive offsets. Full method

Sources

How it’s tested

2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Limits

Rim positions only; a wider tire bulges past the rim on both sides. Check brake, suspension and fender clearance before buying.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: tire dimensions from the size, two sizes drawn to scale, speedometer error dials, wheel offset and backspacing, plus sizing and effective gear ratio.

Every change on What’s new

How we make toolsReport a mistake

Worked example: 7-inch ET40 to 8.5-inch ET30

Half the overall width of a 7-inch wheel, flanges included, is (7 + 1) × 25.4 ÷ 2 = 101.6 mm. With a +40 mm offset its inner edge is 101.6 + 40 = 141.6 mm inboard of the hub face (5.57 in of backspacing) and its outer edge 101.6 − 40 = 61.6 mm outboard.

The 8.5-inch ET30: half width (8.5 + 1) × 25.4 ÷ 2 = 120.65 mm, so 150.65 mm inside and 90.65 mm outside. The outer edge moves +29.0 mm toward the fender and the inner edge +9.0 mm toward the suspension.

Offset, backspacing, poke and inset

Offset (ET, from the German Einpresstiefe) is the distance from the middle of the wheel to the face that bolts to the hub. Positive offset puts that face toward the outside, tucking the wheel in; negative offset pushes the wheel out. Most front-wheel-drive cars use high positive offsets.

Backspacing is the distance from the hub face to the inner edge of the wheel, measured over the flange. The flanges make a wheel about an inch wider than its nominal width (the 8 in 17x8 is measured between the bead seats), so backspacing = (width + 1 inch) ÷ 2 + offset. More options lets you change that allowance if you have measured yours.

Comparing two wheels, the outer edge moves by the change in half-width minus the change in offset, and the inner edge by the change in half-width plus the change in offset. That is what the drawing shows: the old rim dashed, the new one filled, round the same hub face.

backspacing = (width + 1 in) ÷ 2 + offset · poke = Δ(half width) − Δoffset · inner = Δ(half width) + Δoffset

Backspacing by width and offset

Inches of backspacing, with the 1-inch flange allowance.

Backspacing by width and offset
Offset7″7.5″8″8.5″9″10″
-25 mm3.023.273.523.774.024.52
-12 mm3.533.784.034.284.535.03
0 mm4.004.254.504.755.005.50
+12 mm4.474.724.975.225.475.97
+20 mm4.795.045.295.545.796.29
+25 mm4.985.235.485.735.986.48
+30 mm5.185.435.685.936.186.68
+35 mm5.385.635.886.136.386.88
+40 mm5.575.826.076.326.577.07
+45 mm5.776.026.276.526.777.27
Show all 11 rows
+50 mm5.976.226.476.726.977.47

Sources

Common questions

What does a lower offset do?

It moves the whole wheel outward by the difference: ET35 sits 10 mm further out than ET45 on the same width. That widens the track and can rub the fender lip.

Is backspacing the same as offset?

No. Offset is measured from the wheel’s centre, backspacing from its inner edge. Two wheels with the same offset but different widths have different backspacing.

Do spacers change offset?

In effect, yes: a 10 mm spacer acts like 10 mm less offset. Use hub-centric spacers with the right bolts, and check that enough thread engages.