Skip to content

Percent Yield Calculator

Type a reaction, what you started with and what you actually got.

Type a reaction, what you started with and what you actually got. The theoretical yield is worked out for you, and the percent yield is actual over theoretical.

Balanced as CaCO3→CaO+CO2

What you start with

CaCO3

What you actually got

ExamplePercent yield of CaO

91.0%

5.10 g actual ÷ 5.60 g theoretical × 100.

Type your own reaction and amounts.

CaCO3→CaO+CO2

Grams in and out
  • CaCO310.0 g used · runs out
  • CaO5.60 g possible · 5.10 g got
  • CO24.40 g made

Solid: used or made. Faint: left over. The line marks your actual yield.

Theoretical yield
5.60 g
Below theoretical
0.50 g
Limiting reagent
CaCO₃
How this works: 4 sources,

How this works

Method

Percent yield compares what you actually collected with what the reaction could have made: actual yield ÷ theoretical yield × 100. Both must be in the same unit, usually grams. The theoretical yield comes from the limiting reagent and the balanced equation, so that part is worked out first. Full method

How it’s tested

2 worked examples for this page are checked by automated tests before every release: given the inputs, the tool must show the expected answer.

Privacy

On your device. Nothing you enter or open leaves this browser. About privacy labels

Changes

  • First published: molar mass with each element’s share of the mass and atoms, grams to moles and back, percent composition, empirical formula, limiting reagent, theoretical and percent yield.

Every change on What’s new

How we make toolsReport a mistake

How to calculate percent yield

Percent yield compares what you actually collected with what the reaction could have made: actual yield ÷ theoretical yield × 100. Both must be in the same unit, usually grams. The theoretical yield comes from the limiting reagent and the balanced equation, so that part is worked out first.

Heating 10.0 g of limestone, CaCO3 → CaO + CO2: calcium carbonate is 100.086 g/mol, so 10.0 g is 0.0999 mol, which can give at most 0.0999 mol of calcium oxide, 0.0999 × 56.077 = 5.60 g. If the crucible holds 5.10 g of lime afterwards, the percent yield is 5.10 ÷ 5.60 × 100 = 91.0%.

A yield over 100% is a warning, not a success. It usually means the product is still wet with solvent, contains impurities or unreacted starting material, or that a mass was recorded wrong. Yields also multiply across steps: three steps at 80% each give 0.8 × 0.8 × 0.8 = 51% overall, which is why long syntheses are planned around their weakest step.

percent yield = actual yield ÷ theoretical yield × 100

How yields multiply across a multi-step synthesis

The overall yield after a number of steps when every step has the same yield. Computed exactly as the step yield to the power of the number of steps.

The overall yield after a number of steps when every step has the same yield. Computed exactly as the step yield to the power of the number of steps.
StepsAt 95% eachAt 90% eachAt 80% eachAt 70% each
195.0%90.0%80.0%70.0%
290.3%81.0%64.0%49.0%
385.7%72.9%51.2%34.3%
481.5%65.6%41.0%24.0%
577.4%59.0%32.8%16.8%
673.5%53.1%26.2%11.8%
866.3%43.0%16.8%5.76%
1059.9%34.9%10.7%2.82%
1546.3%20.6%3.52%0.475%
2035.8%12.2%1.15%0.0798%

Common questions

What is a good percent yield?

It depends on the reaction. Simple precipitations can come close to 100%, while multi-step organic syntheses are often happy with 50 to 80% per step. Compare against what the method usually gives rather than against 100%.

Can I use moles instead of grams?

Yes, as long as the actual and theoretical yields are both in moles. Switch the unit next to your actual yield and the tool converts it with the product’s molar mass.

Why is my percent yield over 100%?

Most often the product wasn’t completely dry, so trapped water or solvent added mass. Impurities and weighing mistakes are the other usual causes. Dry to constant mass and weigh again.

Is percent yield the same as atom economy?

No. Percent yield measures how much product you actually got. Atom economy measures how much of the reactants’ mass ends up in the desired product even at 100% yield, which is about the design of the reaction.